Jonard

Star Key for LB & LS - SSK-85 The SSK-85 Star Key has a LB 8 point star pattern on one end and a LS 5 point star pattern on the other, and is designed to be used with our SSK-716 Star Key Can Wrench. Also known as a Slam Lock Key. Key is two-sided, just switch from one side to the other for each pattern.
Star Key for LC & LG - SSK-75 The SSK-75 star key has a LG flower pattern on one side and a LC 7 point star pattern on the other, and is designed to be used with our SSK-716 Star Key Can Wrench. Also known as a Slam Lock Key. Key is two-sided, just switch from one side to the other for each pattern.
5 in. Wire Wrapping Bits + Insulated & Non-insulated Sleeves (22 AWG) These wire wrapping bits and sleeves are designed for wire wrapping in areas requiring deep penetration. Their 5" (127mm) length ensures "true" connections in hard-to-get-at locations. The wire wrapping sleeves are available with or without insulation.
5 in. Wire Wrapping Bits + Insulated & Non-insulated Sleeves (26 AWG) These wire wrapping bits and sleeves are designed for wire wrapping in areas requiring deep penetration. Their 5" (127mm) length ensures "true" connections in hard-to-get-at locations. The wire wrapping sleeves are available with or without insulation.
Screwdriver set contains 3 Phillips and 4 Slotted screwdrivers. Kit Includes: INS-475 3/32 X 3 slotted screwdriver INS-4100 5/32 X 4 slotted screwdriver INS-6150 1/4 X 6 slotted screwdriver INS-8175 5/16 X 7 slotted screwdriver INS-180 #1 X 3 Phillips screwdriver INS-2100 #2 X 4 Phillips screwdriver INS-3150 #3 X 6 Phillips screwdriver Convenient rugged tool case Made of 60 CRV (chrome vanadium steel) for strength and durability.  These Insulated screwdrivers are manufactured to IEC 60900 Standards for hazardous work environments. and are tested to 10,000 VAC and rated for 1,000 VAC live use. Handles are made of dual color TPE plastic and the tips are magnetic. Tools are not recommended for use on energized circuits. Work should only be performed by qualified professionals. Do not use this tool if the insulation becomes damaged in any way. Tools must be kept clean and dry. Always inspect before use. Do not touch the uninsulated portion of the tool or any conductive object when either might make contact with an energized source. Always wear approved eye & clothing protection. Only use tools for their designed purpose and always follow OSHA 1910.333 (c)(2) and NFPA 70E 2004 when doing electrical work. Failure to observe proper safety precautions may result in serious injury or death.   Phillips Size PH1, PH2, PH3 Cabinet Slotted Size 1/8" (3.18 mm), 1/4" (6.35 mm), 5/16" (7.93 mm), 5/32" (3.96 mm) Head Type Phillips, Cabinet Slotted Rated To 1,000 VAC Live Tested To 10,000 VAC Standards IEC 60900
10" adjustable wrench. Made of chrome vanadium steel with a chrome plated finish. Forged and heat treated for greater strength. Handle is covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate adjustments use the metric or English scales on either side of the jaws.
12" adjustable wrench. Made of chrome vanadium steel with a chrome plated finish. Forged and heat treated for greater strength. Handle is covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate adjustments use the metric or English scales on either side of the jaws.
6" adjustable wrench. Made of chrome vanadium steel with a chrome plated finish. Forged and heat treated for greater strength. Handle is covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate adjustments use the metric or English scales on either side of the jaws.
8" adjustable wrench. Made of chrome vanadium steel with a chrome plated finish. Forged and heat treated for greater strength. Handle is covered with a red transparent plastic for user comfort. The knurl is precision formed and the operation is smooth and trouble free. For accurate adjustments use the metric or English scales on either side of the jaws.
This 5 piece pocket alignment tool kit contains a selection of the most popular non-conductive tools for aligning and adjusting components. Kit includes: • AT-3767 Trimpot • AT-6241 Alignment Tool • AT-3112 Spudger • S-389 Orange stick • JIC-22035 Probe Pick
Cable Caddy
Jonard
The Jonard Tools CC-2721 Cable Caddy is constructed of sturdy 0.060" thick tubular steel 7/8" diameter. No setup is required, just place it on the floor, remove the cotter pin and load your spools. Includes anti-skid rubber feet to prevent the caddy from sliding while also protecting floors. Will hold Cable spools up to 20" in diameter and 17" in height.
Cable Cutter
Jonard
3/4 inch Coax Cable Cutter - JIC-750 Also known as a Banana Cutter, this cutter is designed to cut 3/4" coaxial cable.   Made from chrome vanadium steel, pliers are heat treated for added strength and longer lasting cutting edges. Tool cuts cleanly without compressed or frayed ends. Functions like a tube cutter - eliminates cable distortion during cable prep. NOT designed to cut steel cable. Yellow plastic handles. 8" long  
Designed to cut up to 1" coaxial cable. This tool works like a tube cutter to eliminate cable deformation during cable preparation. • Tool provides precision one-handed cutting action. • Made from Chrome Vanadium steel with hardened cutting blades. Not designed for ACSR or other steel cables. 8 1/4" long.
Cable Lacing Needle insulated - JIC-3209 Xylan insulated cable lacing needle has a yellow lightweight molded grip handle that will harness or lace multiple lead bundles. 5 1/2" long.
This cable ring tool is designed for cutting the sheathing of inside type plastic, fabric or rubber covered cable 3/16", 1/4", 3/8", & 1/2". Durable metal handle. Tool is supplied with 1 replacement blade.
Drop cable continuity tester - accurate up to 5,000 feet (1,500 m). Identify cables in an MDU, and detect troublesome short circuits. FEATURES: • Loud tone identifies line carrying signal. • LED light indicates splitters, DC shorts and other self grounding devices in cable. • Built-in on/off switch extends battery life. • Voltage protected to 52V. • Right angle male push-on connector for working in confined areas. • Accurate up to 5,000 feet (1,500 m). • High quality AAA battery for operation. • Clear markings on the barrel for use and battery replacement. • Connect the toner without emitting a tone. Now a discretionary option.
The Cable Sheath Stripper and Ring Tool is good for copper cables as well as tight buffer optical fiber cables. Used for butting and stripping cables too large for hand held pliers. Use 1 blade to butt PVC sheathing and use the second blade to strip the sheathing. Adjustable for .018" or .031" thick plastic, rubber or fabric insulation. One spare blade of each style is included with the tool. Also known as CT2860.
Knife / Scissors Combo Designed for stripping, splicing and crimping. The perfect kit for telephone installers. Kit contains the ES-1964 Electrician's Scissor, JIC-22148 Combo Crimper Long Nose Plier and the H-36 Pouch (Made of durable PVC material with metal clip). Set includes slotted leather pouch, snip grip, scissors, scissors grip & knife.  
This compact kit contains a special purpose ergonomic cable splicer's knife, scissor and leather pouch. The knife features a short 1 3/4" tough, cutlery-steel blade and a non-slip handle. The scissors are made of high carbon steel with scraper and file on one sides plus 2 stripping notches.. Both items fit securely in the leather pouch which can be mounted on belts up to 2" wide.
The tough cutlery steel blade is extremely sharp and cuts easily through many types of insulation. It holds its edge with repeated use and features a non-slip easy grip ergonomic handle made from TPR (thermoplastic rubber) for better control and reduced hand fatigue. Blade length is 1¾" and overall length is 6¼"
Three piece kit includes: SSK-716 Can Wrench, SSK-75 Star Key, SSK-85 Star Key. Five-in-One tool. The SSK-716 can wrench is specifically designed to work with our SSK-85 and SSK-75 star keys. The SSK-716 can wrench has two 7/16" hex sockets 1 ½" deep on either ends and can be used to open enclosures that require a 7/16" socket. Also known as a Slam Lock Key. With the SSK-75 and SSK-85 star keys you can open enclosures requiring any of the following star key patterns: LS, LB, LG or LC. The SSK-75 star key has a LG flower pattern on one side and a LC 7 point star pattern on the other. The SSK-85 Star Key has a LB 8 point star pattern on one end and a LS 5 point star pattern on the other. Keys are two-sided, just switch from one side to the other for each pattern.
Double end can socket wrench, 3/8" and 7/16" hex, orange Impact resistant thermoplastic handle available in either our standard or ergonomic can wrench designs. Used in placing fuses in cable terminals and connecting wires to fuses and binding posts. The walls on both sockets are thin enough so they can be used to work locking devices on most terminals and cabinets. 7" long.
Star Key Can Wrench 7/16 - SSK-716 The SSK-716 can wrench has two 7/16" hex sockets 1 ½" deep on either ends and can be used to open enclosures that require a 7/16" socket
FIND & IDENTIFY MULTIPLE COAX CABLES IN MAIN CABLE BOXES For use on Coax Cables for CATV, Satellite Installations, Audio Video Equipment, CCTV and Security & Alarm Installations. The CM-8 Coax Cable Mapper & Toner is designed to quickly find and identify multiple cables and easily map runs to and from a central cable bundle. Features include: • Eight numbered & color coded cable identifiers. • #1 White, #2 Red, #3 Black, #4 Blue, #5 Green, #6 Yellow, #7 Purple & #8 Brown. • Two Alligator clip sets • 1x F-Male coax adapter • 1x F-Female coax adapter • Built-in tone generator • Auto power off 30 minutes in "Tone" mode • Test for Opens and shorts • Auto power off 12 seconds after Pass/Fail results • Maximum cable length for testing 4,000 feet • Powered by two 3V CR2302 batteries • Low battery warning light • Maximum DC cable resistance 100 Ohms • Live Voltage detection Kit contains: • Cable Mapper & Toner • 8 Cable Identifiers (Numbered & color coded) • 2 Alligator Clip Sets • Cordura Case • Instruction Sheet NOTE: This Cable Mapper & Toner will not test cable runs with AC or DC voltage present, Power Amplifiers, Isolation Splitters, Attenuators, Directional Line Tap, Power Dividers or Matching Transformers & DC blocking devices   Click here for replacement terminators
The TK-82 CATV technician's service kit is designed for repair and maintenance of CATV cable networks. Kit Contains: Compression Tool Long Style - CTF-200 6-in-1 screwdriver - SD-61 Cable Stripper RG59/6 & RG7/11 with stop - UST-125 LED Flashlight - FL-2000 Pocket Continuity Tester & Toner - PT-300 High Leverage Diagonal Cutter Plier - JIC-2288 Torque Wrench 30 in./lb - TWAF-71630 Molded Pouch with belt clip - H-85  
Coax Tool Kit with CTF-230 Dual Compression Tool for use on either short or long F connectors (such as PPC EX6 and PPC EX6XL), and also works on most RG 11 connectors. The TK-87 CATV technician's service kit is designed for repair and maintenance of CATV cable networks. Kit Contains: Dual Compression Tool - CTF-230 6-in-1 screwdriver - SD-61 Cable Stripper RG59/6 & RG7/11 with stop - UST-125 LED Flashlight - FL-2000 Pocket Continuity Tester & Toner - PT-300 High Leverage Diagonal Cutter Plier - JIC-2288 Torque Wrench 30 in./lb. - TWAF-71630 Molded Pouch with belt clip - H-85
Coax Tool Kit with CTF-300 Compression Tool for Short Style connectors. The TK-83 CATV technician's service kit is designed for repair and maintenance of CATV cable networks. Kit Contains: Compression Tool Short Style - CTF-300 6-in-1 screwdriver - SD-61 Cable Stripper RG59/6 & RG7/11 with stop - UST-125 LED Flashlight - FL-2000 Pocket Continuity Tester & Toner - PT-300 High Leverage Diagonal Cutter Plier - JIC-2288 Torque Wrench 30 in./lb. - TWAF-71630 Molded Pouch with belt clip - H-85  
7/16-inch combination wrench with box end. Box end offers 12 points of contact. Made from chrome vanadium steel. Total length of tool is 6.5 inches
Fixed Compression Tool - CTF-200 Compression tool with a fixed design for use on many manufacturers F Connectors. Some compatible connectors are: Thomas & Betts: Snap-N-Seal, Digicon: DS6, DS59, DS6Q, DS59Q, DS11, DS7, Gilbert UltraEase: GF-UE-59, GF-UE-59Q, GF-UE-6, GF-UE-6Q, GF-UE-5.1, PPC: CMP6, CMP6Q, CMP59, CMP59Q, CMP11, EX6XL, EX59XL, EX59XLHE, EX6XLWS, EX6LP , EX7, EX7N716, EX11, EX11N716, EX320QR, EX320N716
This dual compression tool is two tools in one, combining the features of the CTF-200 and the CTF-300. It is designed for use on either short or long F connectors (such as PPC EX6 and PPC EX6XL), and also works on most RG 11 connectors. The Green ring side of the plunger is for the “short” PPC EX6 style connectors and the Blue side of the plunger is for the “long” PPC EX6 XL style connectors. Simple to use: Select the proper head size by rotating head to the long or short setting Position the plunger: Green facing the connector for short connectors and Blue facing the connector for long connectors. Pull the plunger to remove and select which side to insert back into tool. Insert the cable and connector in the tool and squeeze Some of the connectors this tool will work on are listed below: PPC: CMP6, CMP6Q, CMP59, CMP59Q, CMP11, EX6XL, EX59XL, EX59XLHE, EX6XLWS, EX6LP , EX7, EX7N716, EX11, EX11N716, EX320QR, EX320N716, EX59XLK, EX6XLK, EX6XLP, EX7N716WS, EX59XLK, EX6XLK, EX6XLP, EX7N716WS, EX11N716WS, EX59XLWS, EX11N716WSPLUS, EX11N716PLUS, EX7N716WSPLUS, EX7N716PLUS, EX6XLPLUS, EX6XLWSPLUS, EX59XLPLUS, EX59XLWSPLUS, EX6XLWS. Digicon: DS6, DS59, DS59Q, DS11,DS7 Belden: SNS11A5TP275, SNS59Q5NS, SNS1P59QS, SNS11A5NS, SNS7ASNS, SNS1P6, SNS59TP275, SNS6TP275, SNS7BNS, SNS1P59, SNS1P59HEL, SNS7BQ, SNS7AS, SNS7B Corning Gilbert UltraEase: GF-UE-59, GF-UE-59Q, GF-UE-6, GF-UE-6Q, GF-UE-5.1, GF-URS-6-SR, GF-URS-59-SR, GAF-URS-11MH. ATX Networks: 9-MPF-CQ
This universal compression tool is designed for use on F Connectors (RG59, RG6, & RG11), BNC Connectors (RG59 & RG6) and RCA Connectors (RG59 & RG6). Tool is designed with a dual head and adjustment dial for each unique connector application. COMPATIBLE CONNECTORS: • PPC - CMP6, CMP62, CMP59Q, CMP11, EX6XL, EX59XL, EX59XLHE, EX6XLW9, EX7, EX7N716, EX11, EX11N716, EX320QR, EX320N716 • T & B - Snap -n-Seal • Digicon - DS6, DS59, DS59Q, DS11, DS7 • Gilbert UE - GF-UE-59, GF-UE-59Q, GF-UE-6, GF-UE-6Q, GF-UE-5.1, RCA-UE, BNC-UE • Plus many other brands and styles including F, RCA & BNC Types.
Compression tool with a fixed design for use on Corning Gilbert Connectors. Tool will work with other brands such as PPC & Thomas Betts. Compatible connectors are: GF-UE, GF-UR, GAF-URS, GF-SFC, GF-EFC Series Connectors.
Fixed Compression Tool - CTF-300 Compression tool with a fixed designed for use on the shorter style F connectors (Such as PPC® Aquatight Connector EX or shorter connectors and other similar length connectors). PPC: EX6/59, EX6W9, EX59HE, EX6P, EX7, EX7N716, EX11, EX11N716, EX320QR, EX320N716 INSTRUCTIONS: 1. Choose the correct head by rotating 2. Open the handle and insert the connector with the cable into the holder 3. Squeeze
Connector-Crimping Pliers with Side Cutters designed to press UG, UR, UY, 709 series connectors, crimping "B" type connectors, and AMP tel splice connectors. A special stop behind cut out prevents damage to connectors. Utilized on combinations of plastic and pulp insulated 19, 22, 24 and 26 gauge copper conductors as well as 20 gauge plastic insulated copper steel wire. Comes with side cutter and yellow handle 5 13/16" long. Also known as PRESSINGC.
Curved Needle Nose Plier - JIC-3385 Nose is bent 60° for maximum visibility. Used in confined areas for bending and forming fine wire. Inside jaws and jaw edges are polished to prevent nicking the wire. Plier has a spring loaded ergonomic design. Length 5 1/2" with a dark blue plastic handle.
CST-1i Cyclops - Fast easy removal of outer insulation from all unshielded twisted pair, shielded twisted pair and multicore cables. The Cyclops features a self adjusting blade and is perfect for PVC and plenum type insulation, plus other materials without damaging the inner braids, foils or conductors. Cable performance is not impacted using this cable stripper. Patented.
High Leverage Diagonal Cutter  with Angled Head Crafted with an angled head for heavy-duty wire cutting in confined spaces, and made of specially forged alloy steel for strength and cutting ability. Red plastic handle 8" long.
Diagonal Pliers - Skinning & Stripping - DIAGB6 Tapered nose diagonal cutting pliers with standardbevel knives with one .045" skinning hole, crusher used for multipurpose wire work, and two V shaped stripping notches. Red plastic handle 6 1/16" long.
Measures 1/2" at both ends. Speed head makes tightening and loosening quick and easy, plus head is angled (15°) to ease access. Speed wrenches are 6 1/2" long. Polished to a high gloss finish, and made of high carbon alloy steel.
Measures 7/16" at both ends. Speed head makes tightening and loosening quick and easy, plus head is angled (15°) to ease access. Speed wrenches are 6 1/2" long. Polished to a high gloss finish, and made of high carbon alloy steel.
Dual Function Wire Wrapping/Unwrapping Bit & Sleeve Set (24-26 AWG)  This innovative Patented product represents a truly revolutionary approach to wire wrapping, by combining both the wire wrapping and the wire unwrapping functions into one bit/sleeve set. The bit is precision machined for high quality wire wrapping in the clockwise direction, but also includes the removal mechanism that is used to unwrap when operated counterclockwise. The user can quickly and easily switch back and forth between wrap and unwrap mode by retracting or extending the retractable sleeve, and flipping the switch on a PTX Wire Wrapping Power Tool. This product, which can wrap or unwrap 22-26 AWG wire (depending on set), enables the user to maximize operating efficiency while eliminating the need to purchase and carry extra tools or bits for unwrapping. Also, to prevent pin-to-pin shorting, the retractable wire wrapping sleeve is coated with a durable 1000V dielectric material.
Electrician Scissors -designed for heavy duty use. Made of high carbon steel with a special hardening process for greater durability and nickel plated for that professional look.The Electrician Scissors are notched to strip 19 and 23 AWG wire and one blade is serrated. A scraper and file are on the back of the blade. Holds edge even when used on fiber and kevlar based cables  
The CSR-1575 is designed to slit and ring cables, buffer tubes and jackets on fiber optic cables up to 7.5mm (0.3") in diameter. The tool features an easily adjustable slit blade and ring blade as well as a removable and reversible V block that improves slitting performance and accommodates smaller to larger diameter cables. Simple to use: • Ringing a cable: Ring blade is easily adjustable using the adjustment knob. Rotate the knob toward the "+" sign to increase cutting blade depth and rotate the knob toward the "-" sign to decrease cutting depth. Once depth is determined, open jaw, insert cable, rotate tool around cable 3 times, open jaw and remove cable, pull off jacket. • Slitting a cable: First select which V groove is needed on the V block, we recommend using the small V groove for cables 3mm or smaller and use the large V groove for cable larger than 3mm. To remove V block simply push on the V block, remove from tool. • Select groove then push V block back into tool. Set the depth of the slitting blade by loosening the screw holding the blade in place, use the tab on the blade to move the blade up or down to the desired slitting depth, tighten screw. Open jaw, insert cable to be slit, close jaw and pull.
The FCT-100 is the perfect tool for inserting and extracting fiber connectors in high density patch panels Tool is designed to work with LC, SC simplex and duplex connectors as well as with MU, MT-RJ and other similar type connectors. The spring-loaded tool and comfortable grips allow for easy operation.   Specifications: • Fiber Connector LC, SC-Simplex, SC-Duplex, MU, MT-RJ • Length 10.6" (269.2 mm) • Weight 1.13 lbs (0.512 kg) • UPC No. 811490018990
The Jonard Tools FCC-125 quick click ferrule end face cleaner is designed to provide exceptional  cleaning performance by cleaning LC connectors beyond the critical fiber core area and cleaning deep into the contact area of a bulkhead adapter or connectors on fiber optic cables. The tethered dust cap provides protection for the micro fiber cleaning fabric and is an adapter for connector end face cleaning. The FCC-125 features a patented 360 degree Rotational Tip for extra wide cleaning, easy one push operation and extendable nozzle, providing an additional 1.5 inches for a nozzle length of 4 inches to aid in accessing deep ports or crowded access panels. Additionally the FCC-125 uses a non-woven micro fiber that is lint free. The FCC-125 provides 800+ cleanings and the outer body is made from static dissipative material for safe ESD work. Patented Cleaning Technology Slide-Guide™ non-slip micro tape feeder guarantees high reliability Dual Rotational tip provides superior ferrule End face cleaning
FCC-250 - Fiber Connector Cleaner 2.5mm The Jonard Tools FCC-250 quick click ferrule end face cleaner is designed to provide exceptional  cleaning performance by cleaning FC, SC and ST connectors beyond the critical fiber core area and cleaning deep into the contact area of a bulkhead adapter or connectors on fiber optic cables. The tethered dust cap provides protection for the micro fiber cleaning fabric and is an adapter for connector end face cleaning. The FCC-250 features a patented 360 degree Rotational Tip for extra wide cleaning, easy one push operation and extendable nozzle, providing an additional 1.5 inches for a nozzle length of 4 inches to aid in accessing deep ports or crowded access panels. Additionally the FCC-250 uses a non-woven micro fiber that is lint free. The FCC-250 provides 800+ cleanings and the outer body is made from static dissipative material for safe ESD work. Patented Cleaning Technology Slide-Guide™ non-slip micro tape feeder guarantees high reliability Dual Rotational tip provides superior ferrule End face cleaning
FCC-120- Fiber Connector Cleaner MPO The Jonard Tools FCC-120 quick click ferrule end face cleaner is designed to provide exceptional  cleaning performance by cleaning MPO connectors beyond the critical fiber core area and cleaning deep into the contact area of a bulkhead adapter or connectors on fiber optic cables. The tethered dust cap provides protection for the micro fiber cleaning fabric and is an adapter for connector end face cleaning. The FCC-120 features a patented 360 degree Rotational Tip for extra wide cleaning, easy one push operation and extendable nozzle, providing an additional 1.5 inches for a nozzle length of 4 inches to aid in accessing deep ports or crowded access panels. Additionally the FCC-120 uses a non-woven micro fiber that is lint free. The FCC-120 provides 500+ cleanings and the outer body is made from static dissipative material for safe ESD work. Patented Cleaning Technology Slide-Guide™ non-slip micro tape feeder guarantees high reliability Dual Rotational tip provides superior ferrule End face cleaning
The FOD-2000 Fiber Optic Drop Cable Slitter is a patented tool that simplifies the slitting of drop cable jackets at the end of the cable or mid-span. For Flat Cables, where the width is .32" and the height is .17". These are the dimensions of a typical corning SST-Drop flat cable. The tool will work on other cables with similar dimensions. The FOD-2000 puts a slit on both sides of the jacket allowing easy access to the fiber or strength member. The ease of use makes this tool truly unique! To use just position the tool around the cable, pull and slit. Designed for .250" flat drop cables. The FOD-2000 comes completely assembled with two blades, which can be reversed once the blades are worn. Replacement blades are also available under part number FOD-RB25.
High carbon stainless steel blades designed to cut Kevlar®, cabling insulation, tape, cable ties and other material. Ergonomic handles for user comfort and durability. Adjustable joint screw under protective cap, serrated blades grip material, sharp and durable 6" long.
Kit includes the JIC-375 Fiber Optic Stripper, ES-1964 Electrician's Scissor, and convenient molded plastic pouch(with belt loop).  
The Fiber Optic Stripper is used for stripping 250 micron buffer coating from 125 micron optical fiber. Preset at the factory so no adjustments are necessary. Unique design prevents nicks or scratches on the optical fiber plus blades are ground and hardened for long life. Yellow plastic dipped handles 5 3/16" long.  
Three hole Fiber Optic Stripper model performs all common fiber stripping functions. The first hole of this Fiber Optic Stripper strips the 1.6-3 mm fiber jacket down to the 600-900 micron buffer coating. The second hole strips the 600-900 micron buffer coating down to the 250 micron coating and the third hole is used to strip the 250 micron cable down to the 125 micron glass fiber without nicks or scratches. Handle is made of TPR (Thermoplastic Rubber) and tool is 6" long.  
An intelligent fiber optic power meter designed to measure wavelengths with high precision. Used for absolute and relative power measurements.   Features: • Measures a wide range of wavelengths • Auto-off feature • Special function allows manual calibration of the unit • LCD back-lite for viewing in low light locations Includes: - Power Meter - Manual - Protective Cover - 3 AA Batteries - Cotton Swabs - (1) FC and (1) SC Adapter - Nylon Carry Case   Specifications Wavelengths Measured (nm): 850, 980, 1300, 1310, 1490, 1550, 1625, 1650 Detector Type:  InGaAs Measurement Range (dBm): -50 +26 Uncer tainty (dB):  ±0.25 Accuracy (dB):  0.01 Auto-of f Time (min)*:  10 Operating Time (h):   ≥130 Bat ter y Type:   3 AA Weight w/o case and bat teries g:   160 g (5.6 oz) Length: 7” (177.8mm) Height: 1.5” (25.4mm) Width: 3.25” (82.55mm) Weight: 1.50 lbs   Click here for a video on the FPM  
Fiber Prep Kt
Jonard
The TK-120 fiber preparation kit provides you with all the tools needed to access and prepare a fiber optic cable for termination. The kit includes: CST-1900, CSR-1575, FOD-2000 and MS-6 for opening various types of fiber optic cables, the JIC-375 fiber stripper and JIC-186 Kevlar cutter for prepping the fiber for termination. Other tools included with the kit are the SD-61 multi bit screwdriver FL-2000 flashlight, JIC-2288 diagonal cutter, JIC-842 long nose plier and FW-5 fiber wipes. All these tools are provided in a rugged tool case (H-90) with extra pockets for extra tools, connectors and many other items.
TK-160 Fiber Prep Kit W/ Connector Cleaners, Visual Fault Locator   The TK-160 Fiber Prep Kit with FCC & VFL (includes the FCC-125 & FCC-250 Fiber Connector Cleaners 1.25mm & 2.5mm and the Visual Fault Locator Kit) . This  fiber preparation kit provides you with all of the tools needed to access and prepare a fiber optic cable for termination. The kit includes: • CST-1900 Round Cable Stripper • CSR-1575 Cable Strip & Ring Tool • FOD-2000 Fiber Optic Drop Cable Slitter •MS-6 Mid Span Slitter for opening various types of fiber optic cables •JIC-375 3-hole fiber stripper •JIC-186 Kevlar cutter for prepping the fiber for termination •SD-61 multi bit screwdriver •FL-2000 LED flashlight •JIC-2288 diagonal cutter •JIC-842 long nose pliers •FW-5 fiber wipes •FCC-125 Fiber Connector Cleaner 1.25mm •FCC-250 Fiber Connector Cleaner 2.5mm •VFL-150 Visual Fault Locator Kit •All these tools are provided in a rugged tool case (H-90) with extra pockets for extra tools, connectors and many other items.
Fiber Scope
Jonard
Fiber inspection microscope has 200x magnification, a focus wheel and features 2.5mm and 1.25mm adapters for use on most fiber connectors. The achromatic lens offers excellent imaging and integrated laser filters for safety (not intended for use with illuminated fibers). Coaxial illumination provides clear view of connector face and fiber. LED light for longer battery life, includes port for illuminating fiber. Rugged cushioned nylon case with belt loop and carry strap and three AAA batteries. Microscope has rubber cover for protection.   • Length:  8.76” (222.50 mm) • Height:  2.25” (57.15 mm) • Width:  1.25” (31 mm) • Weight: 1.570 lbs (0.712 kg) • Magnification:  200x  
Alcohol Wipes. 5 per pack. Pure 99.8% Isopropyl Alcohol. Excellent Cleaner for optical surfaces, glass fibers, and connector end faces Fast evaporating, residue-free solvent Mild, non-abrasive solvent contains no water Compatible with most plastics, glass and metals Convenient, safe package
Alcohol Wipes. 50 per pack. Pure 99.8% Isopropyl Alcohol. Excellent Cleaner for optical surfaces, glass fibers, and connector end faces Fast evaporating, residue-free solvent Mild, non-abrasive solvent contains no water Compatible with most plastics, glass and metals Convenient, safe package
Flaring & Insertion Tool - FT-6 The flaring end of the tool facilitates the expansion of the cable providing easier insertion of "F" connectors. The insertion end makes "F" connector insertion fast and easy, even in cold weather. This tool is recommended for use on polyethylene jacketed cables and plenum cables, and is especially helpful when using tri-shield and quad-shield cables. 4 1/4" long
Made of high carbon steel, this lightweight flush cutter can be used on wire up to 18 AWG while minimizing fly-off. Cantilevered spring automatically opens the plier, and the head fits easily in confined work areas.
A close cutting plier used to trim conductors from the 710 connector modules without leaving exposed conductors. Ideal for close trimming of gates and sprue on injection molded plastic parts. Jaw design aids in use in confined areas. Turquoise color handle, plier is 4 ½" long. Made from chrome vanadium steel.
Head End Tool F Connector Tool - RF-12 Designed to provide easy access to connectors in high-density locations. The head measures 7/16" and is used specifically for "F"connectors. The socket extends 8" from the handle, the overall length is 12" and the back of the handle has an insertion device to aid in making connections
BNC Connector Tool Designed to provide easy access to connectors in high density locations. The head is formed specifically for BNC connectors. The socket extends 8" from the handle and the overall length is 12".
Security Key Insert - SK-51632 Designed with a double-ended hex adapter for two sizes of pin-in-head security fasteners. Simply slip the key into the 3/8" side of a can wrench and you are ready for either a 5/16" or 5/32" hex security screw. The 5/16" side of the SK-51632 is used on tamper-proof cross-connect cabinets, MESA,CATV closures and any other closure that requires a 5/16" tamper proof hex tool to gain access This is a reversible insert tool. One end is for SLC Cabinets and the other is for most Network Interface Boxes.
High leverage design for superior cutting ability. Designed with a shear-type jaw for cutting aluminum and soft copper. Not for use on steel or ACSR type cables. Cuts up to 100-pair cables (24 AWG). Red handle 9 1/2" long.
High Leverage Diagonal Cutter - JIC-2288 Crafted for heavy-duty wire cutting and made of specially forged alloy steel designed for strength and cutting ability. Red plastic handle 8" long.
The perfect kit for simple installations - includes the basic necessities. Kit includes the M-216C/EX Can Wrench, KN-7 Ergonomic Cable Splicing Knife, ES-1964 Electrician's Scissor, JIC-22035 Probe Pick and the H-50 Pouch (made of durable PVC material with metal clip).
K Hook
Jonard
K hook specially designed for push and pull cable installation and retrieval operations. K hook cable to handle cables up to 3/8" diameter. Has standard 8-32 thread for use on fish sticks and glow rods.   Length 5" (127mm) Weight 0.08 lbs
Linemans B Wrench Forged and heat treated, this Linemans Wrench is used on pole line hardware. It is open-end double end type with two sizes of openings at each end and an oval hole for turning pole steps. The end openings accommodate nuts for 3/8", 1/2", 5/8" and 3/4" bolts and the head of the 1/2" drive screw. The faces of the Linemans Wrench openings are offset to provide handle clearance. 13" Long.
Designed for heavy duty use in construction and maintenance work. These pliers are high leverage for cutting bolts, nails, and many gauges of wire including high-strength wire. Cutting edges cut clean and remain sharp. The cushioned-grip, comfortable handles are red plastic dipped to approximately .007". 9 3/8" long. Also known as SIDECUTB9.
Tightens F-Connectors Right The First Time and Every Time. This indoor torque tool is great for connecting coax connectors to consumer electronic devices with the proper amount of torque. Features and Benefits: • Tool is small and compact for getting into tight spaces. 1 3/8” tall and 7/8” diameter. • Glass filled nylon material “work hardens” with use. • Tightens F connectors to 8 to 12 in-lbs of torque (vs. finger tight, which typically produces just 1 to 3 in-lbs of torque). • Consistent torque applied, regardless of the installer. • Eliminates damage to consumer electronic devices due to overtightened connectors. • Prevents service truck rolls caused by loose connectors Helps prevent signal loss, ingress / egress.
Wire Fishing Made Easy! (Click here for the "How-To" video) Quickly threads wire and cable through cavity walls and void spaces. Threads at an angle and safely through other wire and cable obstacles. Saves time, saves money, and sharply reduces the risk of accidents. To use the MM-800 follow these four simple steps: Drill a hole and remove the dust and debris. Next simply place the MM-800 specially designed magnetic rod through the hole you wish to snake the wire. Screw on the appropriate magnetic cap to the cable or wire end and align the magnets. Push the cable into the hole and through the other side of the wall. That's it! 44% TIME SAVINGS Six Sigma certified Dramatically reduces shock risk Easy to use - No experience required Diamond Award Winning Design Each MM-800 Kit Contains: 1 magnetic rod, 2 magnetic extensions and 5 magnetic caps.
Cuts micro ducts and other types of  tubing made from PVC, Nylon, Polyethylene and other materials quickly and with less effort so cuts are clean and straight. Maximum duct diameter 14mm (9/16”). Tool is made from Polypropylene with TPR (Thermoplastic Rubber) grips for comfort. Blade is made from heat treated stainless steel for longer life.   Specifications • Overall Length: 4.5" (114.3mm) • Maximum Duct Diameter: 9/16" (14.28mm) • Weight: 0.115 lbs (52.16g)      
Mid Span Slitter - MS-6 Designed to provide easy access to optical fibers in loose buffer tubes 1.2mm - 3.3mm diameter. With 6 precision grooves, buffer tube slitting is done without damage to the fiber. The blades are replaceable (MSB-1533).   Groove Sizes: 1.2 - 1.5mm 1.5 - 1.8mm 1.8 - 2.1mm 2.1 - 2.5mm 2.5 - 2.9mm 2.9 - 3.3mm   Easy to use: • Select the correct groove. Each groove is marked with the recommended fiber size • Place the fiber in the groove to be used. The arrow on the top of the MS-6 indicates blade location and pulling direction. • Close the tool, make sure the lock is engaged, then pull.   Replacement Blades: MSB-1533    
Mid Span Slitter - MS-26 The Jonard Tools PATENDED MS-26 Mid Span Slitter is designed to open fiber jackets and loose buffer tubes to provide easy fiber access. The MS-26 is designed to work on cables or buffer tubes ranging in size from 2.9mm to 6.8mm in diameter. It's sleek ergonomic design allows you to open a jacket or buffer tube without damaging the fiber and features a replaceable cartridge blade set - part number MSB-2968. The MS-26 was designed with 5 precision grooves which are conveniently identified on the top of the tool. The grooves will handle an assortment of cable sizes. These include: Groove Sizes: 2.9 - 3.6 mm 3.6 - 4.4 mm 4.4 - 5.2 mm 5.2 - 6.0 mm 6.0 - 6.8 mm   Easy to use: • Select the correct groove. Each groove is marked with the recommended fiber size • Place the fiber in the groove to be used. The arrow on the top of the MS-6 indicates blade location and pulling direction. • Close the tool, make sure the lock is engaged, then pull. Replacement Blades: MSB-2968    
LED Flashlight with Zoom Lens - FL-2000 A high quality Osram LED powered by a single AA battery. Housing is rugged aluminum suspended from a clip-on lanyard. Brightness is 120 lumens and the beam is adjustable to meet the working environment.   Zoom in for a tight narrow beam and zoom out for a wide light. Hold the head of the flashlight with one hand and the body with the other. Simple in and out movement adjusts the light.  
Modular Cable Tester. The MCT-468 is designed to check and troubleshoot the pin connections of RJ45, RJ12, and RJ11 connectorized cables. It is ideal for testing the continuity of a cable with RJ11 or RJ45 connectors prior to installation.   Features: • Can test RJ45, RJ12, and RJ11 terminated cables • Tests for opens, shorts and miswiring • Full LED indication lights on both main and remote unit. • Auto tests when switched on • Move switch to S to slowdown auto test feature • Small size and lightweight • Carry case included • Uses a 9V battery (included)
Molded Pouch
Jonard
Molded Two Tool Pouch is made of durable PVC material with metal clip. Used in or the TK-22148 and TK-375.  
The TET-700 multifunction cable tester is used to test continuity on RJ45 cables, BNC & F connectorized coaxial cables and other non connectorized cables; it also provides tone via the RJ45 and BNC connectors as well as the test clips. The TET-700 provides Talk power to a telephone for testing. The TET-6 accessory kit is included with the TET-700 , it includes: (2) BNC to F connector adapters (1) 50 ohm BNC terminator (1) Belt Clip (1) BNC cable jumper (1) F connector Jumper (1) RJ45 cable jumper
Designed for use on 110 terminal blocks. A non-impact punchdown tool. Perfect for do-it-yourself small jobs on a 110 terminal block. Fits neatly in the palm of your hand. Quickly and easily switch from cutting and non-cutting blade side with one hand. Simple - Fast - Easy. PATENT PENDING.
Hollow Shaft Nut Driver (3/16") These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7"
6-IN-1 SCREWDRIVER The SD-61 Jonard 6-in-1 Screwdriver eliminates the need for multiple tools in your belt. Soft rubber handle offers comfort and ease of use. The end of the handle is marked to identify the tool.   This tool is configured to include:  • #1 & #2 Phillips Head  • 9/32" & 3/16" slotted heads  • Two nut drivers 5/16" & 1/4"  • The tool is made of special alloy steel for exceptional strength, long life and helps prevent corrosion.      
Hollow Shaft Nut Driver (1/2") These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7"
Hollow Shaft Nut Driver (1/4") These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7"
Hollow Shaft Nut Driver (5/16") These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7"
Hollow Shaft Nut Driver (7/16") These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7"
Jonard 7-piece nutdriver cushion grip set. 3/16, 1/4, 5/16, 11/32, 3/8, 7/16, 1/2.   These are full length hollow shaft nut drivers intended for working with long bolts. They are designed with cushion gripped ergonomic color coded handles. Handles provide greater torque and user comfort. Overall length 7".
Manufactured with a secure tongue and groove design for a non-slip grip (even under heavy pressure). Made from high quality tool steel, this 10 inch plier offers a wide range of jaw openings -with a smooth, positive interlock between halves. Red plastic dipped handle with an overall length of 10"
Manufactured (Jonard) with a secure tongue and groove design for a non-slip grip (even under heavy pressure). Made from high quality tool steel, this six inch plier offers a wide range of jaw openings -with a smooth, positive interlock between halves. Yellow plastic dipped handles.
Manufactured with a secure tongue and groove design for a non-slip grip (even under heavy pressure). Made from high quality tool steel, this six inch plier offers a wide range of jaw openings -with a smooth, positive interlock between halves. Yellow plastic dipped handle with an overall length of 6 3/4"
Punchdown Blade For 630 Modular Jack EPB 630 modular jack Punchdown Blades are compatible with all industry standard twist and lock style punchdown tools.
66 & 110 Blade Combined With Cutter 66 & 110 combination Blade with cutter. Jonard EPB Punchdown Blades are compatible with all industry standard twist and lock style punchdown tools. Made of hardened alloy steel and nickel plated.
66 & 110 Blade Combined With Cutter 66 & 110 combination Blade with cutter. Jonard EPB Punchdown Blades are compatible with all industry standard twist and lock style punchdown tools. Made of hardened alloy steel and nickel plated.
Punchdown Tool with 66 Punch & Cut Blade   Sleek ergonomic design for easy effective wire termination.   Features include: • Hi/Low impact setting • Combination Hook/Spudger stored in the chassis • Color coded yellow on the CUT side • Enlarged blade storage compartment Use to properly set, seat and terminate wire. Simply position the wire, push tool, and listen for confirming pop. Wire is properly seated.  
Punchdown Tool with Combination Cut Blade 66 & 110   Sleek ergonomic design for easy effective wire termination.   Features include: • Hi/Low impact setting • Combination Hook/Spudger stored in the chassis • Color coded yellow on the CUT side • Enlarged blade storage compartment Use to properly set, seat and terminate wire. Simply position the wire, push tool, and listen for confirming pop. Wire is properly seated.  
EPD-91461 Punchdown Tool with two Cut & Punch Blades (66 & 110)   Sleek ergonomic design for easy effective wire termination.   Features include: • Hi/Low impact setting • Combination Hook/Spudger stored in the chassis • Color coded yellow on the CUT side • Enlarged blade storage compartment Use to properly set, seat and terminate wire. Simply position the wire, push tool, and listen for confirming pop. Wire is properly seated.  
A technician's Service Kit designed for maintaining telecommunications and data communications networks. Kit Contains: EPD-914 Punchdown Tool 66 Blade with & without cutter 110 Blade with & without cutter CST-1i Cyclops UTP/STP Cable Stripper FL-2000 LED Flashlight with Zoom Lens JIC-22035 Probe Pick Spudger JIC-22148 Combo Crimper Long Nose Plier SD-61 6-In-1 Screwdriver ES-1964ERG Ergonomic Electrician Scissor H-75 Molded Pouch.
Ratcheting Cable Slitter   Features: • Slits and rings PVC, PE, rubber, and other cable jacket materials. Will work on small cables as well as cables larger than 25mm. • Designed with reversible double-ended replaceable blade with adjustable cutting depth 0-5mm for each unique cable application. • 10/20/30mm scaled on tool for slitting length reference. • For midspan or end cable slit and ring applications.   Specifications • Cut Type Slit, Ring • Weight 0.4 lbs (181.43g) • Length Open 8-1/4" (209.55 mm), Closed 6" (152.4 mm) • UPC No. 811490018822
1/2-inch ratcheting combo wrench with speed head. Combination wrench measures 1/2" at both ends. The speed head makes tightening and loosening quick and easy while the ratcheting box end with 12 points of contact makes this the perfect tool for cable and satellite installers. Designed to work on F Connectors on splitters and all 7/16" connections - this wrench is polished to a high gloss finish and made of chrome vanadium steel and just 6 1/2" long.
7/16-inch ratcheting combo wrench with speed head. Combination wrench measures 7/16" at both ends. The speed head makes tightening and loosening quick and easy while the ratcheting box end with 12 points of contact makes this the perfect tool for cable and satellite installers. Designed to work on F Connectors on splitters and all 7/16" connections - this wrench is polished to a high gloss finish and made of chrome vanadium steel and just 6 1/2" long.
Replacement Blades For MS-26 Replacement Blade Set 2.9 - 6.8mm (pkg of 2) for MS-26 Mid-span Slitter   For use with MS-26    
Replacement Blades For MS-6 Replacement Blade Set 1.2 - 3.3mm (pkg of 2) for MS-6 Mid-span Slitter   Cable Diameter 3.2-9.6 mm, 3.2-9.6 mm Capacity 1.2-3.3mm UPC No. 811490016682 For use with MS-6    
The CST-1900 is designed for fast and precise jacket removal of PVC, rubber, PE and other jacket materials, and works well on round cables with diameters ranging from 3/16" to 1-1/8" (4.5-29 mm). This is a Triple Action Tool, cutting longitudinally for end stripping, spiral for end stripping and mid-span cuts, and circular for jacket removal. A simple versatile easy to use tool your customers will love. The Replaceable Cutting Blade CST-7915 is spring loaded, adjustable for various cable diameters, provides a 90 degree blade rotation and is designed for long life.   Cut Type:        Slit, Ring Cable Type:    Jacket, Round Distribution Cable Dia:      4.5-29.0 mm Material:        Metal Length:           5-1/4" (133.35mm)
Jonard Philips Head Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Phillips #1 x 3" 
Jonard Philips Head Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Phillips #2 x 4" 
Jonard Philips Head Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Phillips #3 x 6" 
Jonard slotted Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Slotted 1/4" x 4"
Jonard slotted Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Slotted 3/16" x 3"
Jonard slotted Screwdrivers are made of special alloy steel for exceptional strength, long life and helps prevent corrosion. Precision machined for that perfect fit. Offers accurate size for maximum torque without slippage. Soft rubber handles offer comfort and ease of use. The end of the handle is marked to identify the tool's size. Slotted 3/16" x 6"
Jonard Slotted Screwdrivers are made of special alloy steel for exceptional strength, long life and corrosion prevention. The slotted screwdrivers have cabinet tips to allow easy access where space is limited. Soft rubber handles offer comfort and greater torque. The end of the handle is marked to identify the tool's size, and the tips are magnetic. Meets applicable ASME/ANSI specifications. Slotted 5/16"x 6" Overall Length: 10 3/8" (264mm)
SDC-3810 - Screwdriver Slotted 3/8" X 10" Jonard Slotted Screwdrivers are made of special alloy steel for exceptional strength, long life and corrosion prevention. The slotted screwdrivers have cabinet tips to allow easy access where space is limited. Soft rubber handles offer comfort and greater torque. The end of the handle is marked to identify the tool's size, and the tips are magnetic. Meets applicable ASME/ANSI specifications.
Red Tip Bat-Handle Pedestal Lock Security Tool. Single plunger activation.   The TTB-6 Barrel Lock Plunger Key is compatible with several types of Highfield and Innertite barrel locks with inside diameters ranging from 0.176” to 0.196”. Compatible with Channell Highfiled and InnerTite CATV barrel locks. The barrel lock plunger key is compatible with several types of Highfield and Innertite barrel locks with inside diameters ranging from .176" to .196". Works on Channell LK03029817, Highfield 93180775-S. This key may also fit other locks used in the electric, gas and water utilities. Know your lock size before purchasing. The key is made of high carbon alloy steel, designed for heavy duty use and engineered for superior tamper resistance. Smooth plunger and heavy duty spring for strength and durability, and serialized for added security. For authorized personnel only.
Used with 7/16" hex shielded F Connectors. Design includes extended 7/16" shank for ease of use with Torque Wrenches in security shield applications. Machined and heat-treated steel for maximum durability with black oxide finish. Knurled handle for secure gripping and includes a steel loop for turning leverage and carrying.  
Security Shield Trap Tool - SST-916 Used with 9/16" Hex shielded F connectors (RG11 connectors) . Machined and heat treated high carbon steel for maximum durability with a nickel plated finish. Loop attachment to allow for connecting to your key ring or carabiner for easy access. Shaft Length 1.625".  
Security Shield Tool (WS) Security Shield Tool - SST-716AT Used with 7/16" hex shielded F Connectors. Design includes extended 7/16" shank for ease of use with Torque Wrenches in security shield applications. Machined and heat-treated steel for maximum durability with black oxide finish. Knurled handle for secure gripping and includes a steel loop for turning leverage and carrying. Note: SST-716AT is designed for use where security shield applications for PPC AquaTight® EX Series connectors are used.
Short Nose B Type Pliers - BSHORTNOSE Intended for use in skinning 22-24 AWG wire and crushing insulation in nose slot. The front portion of the jaws is narrowed, and a portion of the inner face of one jaw is relieved to skin insulation from wire. The inner surface of the jaws are serrated to facilitate gripping wire. Orange color handle 6 3/16" long. Ask for the CSHORTNOSE which is identical to the BSHORTNOSE but has an aluminum oxide insulating coating on the outside nose surface.
Spudger
Jonard
Probe Pick Spudger - JIC-22035NT Tough resilient yellow nylon insulating probe "spudger". One end is tapered to a 1/16" diameter with an uninsulated 'L' shaped wire hook extension. The other end tapers to a flat, 3/16" wide and 1/16" thick, with 2 small notches. Used in electrical contacts. 7" long.
SSK-800 - Star Key Can Wrench Kit for LG & LB Patterns The SSK-716 can wrench is specifically designed to work with our SSK-80 series of star key inserts. The SSK-716 can wrench has two 7/16" hex sockets 1 ½" deep on either end and can be used to open enclosures that require a 7/16" socket. With the SSK-80 star keys you can open enclosures requiring any of the following star key patterns: LG LB  
Strip Tool
Jonard
Universal Cable Stripping Tool Coaxial Cable Stripper Tool Coaxial Cable Stripper (RG59/6 & 7/11 with Stop)
Strip Tool
Jonard
Universal Cable Stripping Tool Use for Coax, Round Network Cables and Flat Cables. This versatile tool is five tools in one. Simply reverse the cassette for RG59/6 & 7/11 Coax Cables. Insert the Round Cable into the second hole (adjustable) for a fast and easy strip. The third hole is for cutting all styles of cable while the fourth hole is designed for Flat Cable and 4P/6P style cable. The perfect wire stripper for most stripping applications.   Replacement Blade: UST-205
Strip Tool
Jonard
Universal Cable Stripping Tool   Coaxial Cable Stripper Tool Coaxial Cable Stripper (RG59/6 & 7/11)       Replacement Blade: UST-205  
Strip Tool
Jonard
Universal Cable Stripping Tool     Coaxial & Telephone Cable Stripper Tool - UST-150 The UST-150 is designed to strip both RG59/6 and UTP (Untwisted Pair) cables . Works equally well if you are left handed or right handed.       Replacement Blade: UST-215  
Coax Stub End Strip Tool RG59/6 The CSS-596 is a coaxial cable stripper specifically designed to strip the stub end of a coax cable in a wall outlet. This tool eliminates the need to run new cable thereby saving time and money. Easy to use, insert cable, rotate like a screwdriver and remove Tool will not cut the braid or score the center conductor Blades are easily changed and replaced
Wire Stripper & Cutter The latest development in wire stripping & cutting. Simply place the wire in the stripping slot. Squeeze and pull. The wire is stripped and cut to the exact length required. Comes with cushioned ergonomic grips, interchangeable blades 22-24 AWG and 24-26 AWG. Supplied assembled.    
Stripper Wire Stripper and Cutter The JIC-1626 Wire Stripper and Cutter is designed to strip and cut the most commonly used stranded and single wire gauges 16 to 26 AWG   Other features include a coil spring opening to reduce fatigue, wire looping, bending holes conveniently located, black oxide finish, locking mechanism, and cutting surfaces that are hardened, tempered and ground for superior performance. 6 ¾" long and weighing just 4.5 ounces.  
Stripper Wire Stripper and Cutter The JIC-2030 Wire Stripper and Cutter is designed to strip and cut the most commonly used stranded and single wire gauges 20 to 30 AWG   Other features include a coil spring opening to reduce fatigue, wire looping, bending holes conveniently located, black oxide finish, locking mechanism, and cutting surfaces that are hardened, tempered and ground for superior performance. 6 ¾" long and weighing just 4.5 ounces.  
Stubby #2 Phillips Screwdriver Jonard Stubby Phillips Screwdrivers are made of special alloy steel for exceptional strength, long life and corrosion prevention.   Soft rubber handles offer comfort and greater torque. The end of the handle is marked to identify the tool's size, and the tips are magnetic. Meets applicable ASME/ANSI specifications. Overall Length: 3-1/2" Weight: 1.9 oz    
Stubby Slotted Screwdriver Jonard Stubby Screwdrivers are made of special alloy steel for exceptional strength, long life and corrosion prevention.   Soft rubber handles offer comfort and greater torque. The end of the handle is marked to identify the tool's size, and the tips are magnetic. Meets applicable ASME/ANSI specifications. Overall Length: 3-1/2" Weight: 1.9 oz
Angled Speed Wrench Stubby 7/16 Speed Wrench Double-Ended Stubby, measures 7/16" at both ends. Speed head makes tightening and loosening quick and easy, plus head is angled (15°) to ease access. Chrome plated, polished to a high gloss finish, and made of Chrome Vanadium steel.  • Wrench Type:   Speed •  Size:         7/16" • Length:   4" • Head Angle:  15 Degrees
Tamper proof wrench for use on tamper-proof cross-connect cabinets, MESA and CATV closures. Recessed at both ends, 1/4" deep. Red plastic handle for user comfort.
Tapered nose diagonal cutting pliers with standard bevel knives with .030" and .045" skinning holes, with crusher used for multi-purpose wire work, with two V-shaped stripping notches. The comfortable handles are red plastic dipped. Made of chrome vanadium steel.
Pliers are for general use looping, bending and cutting. Grips small wires and parts and reaches into tight spaces. Jaws are knurled, serrated and have side cutting blades. Cushion gripped yellow plastic handle 6 7/8" long.
Modular Crimping Tool 6 in 1 - UC-864 This is a modular crimping/stripping connector tool for voice and data applications. Designed to cut, strip and crimp paired conductor cables (round STP/UTP and flat satin phone cables). Cable parameters: 28-22 AWG (.08 - .34mm) flat or round,solid or stranded, telephone or data. Crimps: 4, 6 & 8 position modular connectors (RJ22, RJ11, RJ12 & RJ45).
RJ11, RJ45 Regular and Feed-Thru Connector Crimper Tool   Durable all-steel construction crimp tool with built-in cutter and stripper.   Features: • Crimp and trim off excess conductors with a simple squeeze of the tool • Cleanly shears excess conductors leaving a smooth flat finish • Ratcheted, ultra-stable platform for consistent terminations with low hand force • Tool includes built in jacket stripper for round cables as well as flat cables plus a flat cable cutter • Crimping dies are precision ground. Crimps 2,4,6 and 8 position RJ-11 and RJ-45 regular and feedthrough type modular connectors • Heavy duty cutting blade good for 3,000 cuts • Ergonomic handles for greater comfort       Instructions for use on RJ-11/RJ-45: 1.   Strip and remove cable jacket and untwist pairs 2.   Insert wires into connector until extending though the connector and jacket is inserted into connector 3.   Insert connector completely into appropriate crimp cavity in the tool and squeeze handles together to crimp connector and cut excess wire. Remove connector from Tool    
The RDT-18K is the perfect tool to install or retrieve a cable in drop ceilings or other hard to reach places. This Telescopic Pole is self-supporting, so it is perfectly suited for spanning ceilings and voids to route or retrieve cable. Simply grab the wire with our hook and expand or contract the pole as needed. The Jonard Tools RDT-18K Telescoping pole is constructed with a series of tapered tubes which interlock and extend a full 18 feet, collapsed length is only 33 inches. The pole is made from an improved fiberglass material with a polyester resin baked enamel coating for greater durability and resistance to splintering. The RDT-18K is considerably more rigid than rod or coil based products, and gives the installer far more control and greater accuracy over longer distances. The RDT-18K telescoping pole comes with two convenient hooks to help grab and/or push cables: One C type hook and a K hook. Plus a special adapter for tight applications. When not in use, the RDT-18K is compact and lightweight and is easily carried using the shoulder strap. It has an elastic band with slots to hold the hooks provided so they are readily available when you need them. To prevent the pole from opening when not in use, make sure the rubber stopper is securely fitted into the housing of the main body. Weighs 2.4 lbs. The RDT-18K is the perfect tool to use when installing the Magtime Magnetic cable holders in high locations. The pole allows the user to install the magnetic cable holders in locations up to 18’ without the use of a ladder, a real time saver.   Length:   • 18 Feet (Extended),   • 33 inches (Collapsed) Weight:   • 2.406 lbs    
Has Gilbert plunger style terminator on one end and the Viewsonics (2-prong& 3 prong) terminating tool on the opposite end of the tool to work both the Viewsonics 2&3 prong terminator. Tool is used for various locking terminators including the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), and SV-LT & SV-LTA (Signal Vision) locking terminators. Ergonomic handle provides greater leverage and a superior grip.
Termination Tool Gilbert plunger type, short termination tool. Tool is used for various locking terminators including the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), and SV-LT & SV-LTA (Signal Vision) locking terminators. Ergonomic handle provides greater leverage and a superior grip.  Terminator Tool 2 ½" shaft, overall length 4 ½"
Termination Tool Gilbert plunger type, long termination tool. Tool is used for various locking terminators including the Gilbert Engineering GTP (Morlock), PRC (Production Products Company), LFT, PCT (International Technology), TPG, TR 75 GTL (Viewsonics), and SV-LT & SV-LTA (Signal Vision) locking terminators. Ergonomic handle provides greater leverage and a superior grip. Terminator Tool 4” shaft, overall length 8"
Termination Tool Gilbert short cam style locking security tool. A Cam Style locking terminator tool for Corning Gilbert style terminators. Works on Gilbert NS-5762-3 (plus -9, -11, -13 & -15 terminators). High quality aluminum construction, blue color and is 5" long.
Termination Tool Gilbert Long cam style locking security tool. A Cam Style locking terminator tool for Corning Gilbert style terminators. Works on Gilbert NS-5762-3 (plus -9, -11, -13 & -15 terminators). High quality aluminum construction, blue color and is 9" long.
Multi-Function Cable Tester Toner & Probe Kit Ideal for VDV (voice - data - video) professionals in telecommunications, network and digital communications. This is a multi-function cable tester for RJ45 LAN cable, BNC/F coaxial cable, 6P2C/4P2C jacks and provides tone generation. Kit includes: Cable tester, tone tracing probe (2) BNC male to F female connectors BNC cable terminator 50Ω RJ45 jumper Two 9V batteries Nylon bag, belt clip, & user's manual
Proper connectorization at ‘F’ connector interface with factory preset torque setting. Audible ‘clicking’ sound to indicate proper calibrated torque. Basic Angled head model. Torque in Newton Meters: 2.26. Torque in inch pounds: 20
Proper connectorization at F connector interface with factory preset torque setting. Audible clicking sound to indicate proper calibrated torque. Basic Angled head model. Torque in Newton Meters: 3.39 Torque in inch pounds: 30  
Two tools in one - a trap wrench with a security wrench. The perfect tool for all standard traps and equally adaptable for all sizes of metal security shields (The security wrench fits all metal 7/16" hex fittings). Made of lightweight aluminum with a security socket made of hardened steel for longer life. Lightweight just 2 oz. (57g) and just 7 1/2" long
The new, FCC-300 Universal Fiber Connector Cleaner incorporates a new non-woven, synthetic cleaning cloth offering greater durability, usability and improved reliability. And this cloth can handle wet or dry cleanings and there is never a fiber residue on the end face. The FCC-300 results in a handheld connector cleaner that is strong enough for aggressive cleaning of a wider range of contaminates, soils and end-face debris. Stable, consistent, cleaning performance regardless of operator skill thanks to its patent pending Slide-Guide™ connector holder. Key Features: Extra durable, compact and highly reliable cleaner for connector end-face suitable for cleaning in the field and factory. Automatic “Clean and Advance” tape technology provides a fresh cleaning surface for each use eliminating waste and guaranteeing long tool life. Packaged in a handy palm sized unit, for over 500 cleanings. Works with both Simplex or Duplex applications. ESD Anti-static materials. Supports both PC and APC end face designs. Applications: Customer premises, troubleshooting / maintenance Pedestals, COs, Head-Ends, Routine Testing Installation / Assembly / Production environments Applicable Connectors: Simplex FC, SC, ST, LC and MU (For PC and APC) Duplex LC/PC (Standard Pitch 6.25 and Narrow Pitch 5.25mm) Duplex MU/PC (Standard Pitch width 4.5mm)
This pen style VFL is specially designed for field personnel who need a portable light source tool for fiber tracing, fiber routing, continuity testing, to locate breakpoints (bending or cracking in fiber optic cables), and poor connections.  The VFL works in an OTDR dead zone and is used for end-to-end visual fiber identification. Operates in either CW (continuous wave) or pulsed mode. Not recommended For use on dark colored or armored cables.   Specifications: Light Source: Class IIIA Laser Diode 5mw Wavelength: 650nm Battery Life: 60 Hours Connector: 2.5mm universal Working Temperature: -4F (-20C) to 140F (60C) Storage Temperature: -40F (-40C) to 185F (85C) Power: 2 AAA Batteries (included)
Visual Fault Locator Kit - Includes: VFL-25, 2 AAA Batteries, VFL-25125 FC/LC Adapter. This pen style VFL is specially designed for field personnel who need a portable light source tool for fiber tracing, fiber routing, continuity testing, to locate breakpoints (bending or cracking in fiber optic cables), and poor connections. VFL-150 works on FC, SC, ST connectors and will work on LC connectors when used with the included VFL-25125 adapter. The VFL works in an OTDR dead zone and is used for end-to-end visual fiber identification. Operates in either CW (continuous wave) or pulsed mode. Not recommended For use on dark colored or armored cables. The kit includes: • VFL-25 Visual Fault Locator • VFL-25125 Adapter For VFL FC-LC   Specifications: Light Source: Class IIIA Laser Diode  5mw Wavelength: 650nm Battery Life: 60 Hours Connector: 2.5mm universal Working Temperature: -4F (-20C) to 140F (60C) Storage Temperature: -40F (-40C) to 185F (85C) Power: 2 AAA Batteries  
30' Glow Rod Kit 3/16" Diameter extends a full 30 feet. These glow rods (made of luminescent fiberglass) are designed to provide splinter free use over the life of the product while also providing excellent flexibility. The luminescence of the rods is brighter and lasts longer than the competition. The metal ends of the rods are secured in place and provide superior strength. The threads on the metal ends are standard 8-32 so the rods and accessories can be used with many other manufacturers glow rods. The Jonard Tools' RDG-30 Glow Rod Kit includes: • Six 5 foot long Rods, 3/16" diameter, for greater flexibility • Eyelet • Ball Chain attachment • Wisk • Hook • Kit packaged in clear reusable plastic tube
Wire Stripper and Cutter The JIC-1022 Wire Stripper and Cutter is designed to strip and cut the most commonly used stranded and single wire gauges 10 to 22 AWG and 2-3 mm fiber jackets. Other features include a coil spring opening to reduce fatigue, wire looping, bending holes conveniently located, black oxide finish, locking mechanism, and cutting surfaces that are hardened, tempered and ground for superior performance. 6 ¾" long and weighing just 4.5 ounces.  Wire Stripper and Cutter 10-22 2.60-0.64 mm  
Wire Wrap Gun
Jonard
PTX Electric Wire Wrapping Tool The patented PTX Series of Wire Wrapping Tool brings a new level of wire wrapping proficiency to installers, telecom technicians and other users.   This wire wrapping tool has a maximum usage rating of 2,500 cycles/day, will wire wrap 18 to 30 AWG wire and is available in both battery and electric models. The PTX also features a dual-finger short-throw trigger, a long handle to mitigate pressure on the palm to prevent repetitive stresses and a comfort design based on the recommendations of our certified ergonomist. The housing is rugged yet light in weight and includes additional features including a wrap unwrap switch, a high-powered motor for the heaviest gauges of wire and a permanently attached collet nut. Besides being available in both a battery and electric models, the electric PTX Wire Wrapping Tools are available with a unique optional feature known as backforce. * * Backforce is a spring-loaded internal device that is utilized to help the operator eliminate excess pressure against connections on critical applications. The succeeding turns of wire being wrapped on the terminal forces the wire wrapping bit rearward against a predetermined spring pressure. This assures that every connection on the panel has been wrapped at the same pressure. The backforce wire wrapping feature is recommended for new users/trainees and is best when used on wire gauges 26 to 30 AWG. Ergonomic Design - Minimizes Repetitive Stress A 20' Long Power cord Rugged Construction for Field Usage Battery and Electric Powered Versions Available Wraps and Unwraps 18 to 30 AWG Wire Rated Maximum Usage: 2,500 cycles/day  
Wrap-Unwrap Tool, 24-26 AWG This two sided wire wrapping and unwrapping tool is intended to be two tools in one. It is designed to produce perfect wire wrapping connections. Precision, long-lasting tools for use where occasional wire wraps are required or where power wire-wrapping tools are not practical. Compact and convenient. To switch from wire wrapping to unwrapping takes only seconds - just a quick change of the cap from one end to the other. Wrapping Side: Regular Wrap.