Aerial

Lightweight, compact grips pull an exceptionally wide range of cable sizes and types. Designed with a round inside-jaw contour for maximum contact to minimize conductor damage. Lower jaw is serrated to firmly grip insulated cables and conductors. Design includes a latch that prevents the grip from falling in case of jaw disengagement from the cable.   Features • Lightweight, compact grips pull an exceptionally wide range of cable sizes and types • Designed with a round inside-jaw contour for maximum contact to minimize conductor damage • Lower jaw is serrated to firmly grip insulated cables and conductors • Design includes a latch that prevents the grip from falling in case of jaw disengagement from the cable • Large-diameter eye accommodates large hooks on hoists, winches and tackle blocks   Specifications • Type: Compact • Application: Cable Pulling • Special Features: Hot Latch, Spring • Overall Length: 11.7'' (29.7 cm) • Cable Type: Messenger, EHS, Guy Strand • Cable Diameter: 0.625'' to 1.25'' (15.87 to 31.75 mm) • Hot Latch: Y • Swing Latch: N • Spring: Y • Locking Handle: N • Jaw Type: Round - Serrated • Jaw Length: 4.5'' (11.4 cm) • Maximum Safe Load: 7500 lb (3400 kg)
Web-Strap Ratchet Arial Hoist Klein Tools' Web-Strap Ratchet Hoist features a tighter ratchet to reduce work and fatigue. The handle and drum knob allow you to safely control the tension release to avoid free wheeling. The hoist can be used in both a single line and double line configuration. The handle provides a 360 degree range of motion for easier adjustment from any angle.   Features • Large, non-conductive dial (drum knob) allows web slack to be adjusted with ease • 360-degree handle rotation • 3/4-ton single line and 1-1/2-ton double line load rating • Tight ratcheting mechanism allows precise tensioning • Meets ANSI/ASME B30.21-2014 and B30.10-2014 standards • Has a single line pulling distance of 20-Inches to 138-Inches (50.5 to 350.5 cm) • Hoist can be used with either a single line or a double line     Specifications • Single Line Pulling Distance: 20'' to 138'' • Single Line Load Rating: 1500 lb • Double Line Pulling Distance: 26'' to 79'' • Double Line Load Rating: 3000 lb • Weight: 12.5 lb  • UPC: 092644614255        
Dead-end bracket used to apply tension to steel strand building riser and to provide a means to dead-end a guy strand.  • Mechanically galvanized ASTM B695 • 1,000 lb load capacity • 5/16" diameter hook with 2-3/4" tension adjustment.   
Lemco's SG-24 shotgun arm / cable block pusher can be used between the lasher and the cable guide chute when lashing aerial cable. A SG-24 mounted in front of a lasher serves as a spacer for the cable guide (and multi-cable positioners, if required) during drive-off installations. In back-pull installations the arm pushes cable blocks located mid-span to the next pole for removal as the cable is being lashed. Features • Zinc Plated • Fabricated of a steel tube and bearing flanges • Lock-pins retain the pusher to the strand Specifications • Strand up to: 9⁄16” in diameter • Length: 24 in • Weight: 2 lbs  
Lemco's SG-40 shotgun arm / cable block pusher can be used between the lasher and the cable guide chute when lashing aerial cable. A SG-40 mounted in front of a lasher serves as a spacer for the cable guide (and multi-cable positioners, if required) during drive-off installations. In back-pull installations the arm pushes cable blocks located mid-span to the next pole for removal as the cable is being lashed. Features • Zinc Plated • Fabricated of a steel tube and bearing flanges • Lock-pins retain the pusher to the strand Specifications • Strand up to: 9⁄16” in diameter • Length: 40 in • Weight: 3 lbs  
UNIVERSAL HEAVY-DUTY CABLE BLOCK PUSHER This simple tool makes the lashing process smoother by maintaining the proper cable lead between the lasher and the cable block. • The slotted tube has rotatable sleeves at each end to lock the unit on the strand • Standard length 24 in. (61cm) • Weight: 2.4 lbs. (1.1kg)
Strand Brake
Lemco
The Lemco Strand Brake offers safety and productivity to the strand crew. The three-bolt clamp does not have to be opened or closed for installation or removal. The avoidance of traffic accidents and private property damage in easements is gained productivity. The brake replaces most multiple splices, set-ups, and increases the length of runs.   Features • Works well on 1/4", 5/16" and 3/8" strand. • During pull-out it is 'free-running' as the brake creates no drag and does not scrape the strand's galvanized coating. • Plated steel, stainless steel harness cable. • Wt. 1.1 lbs.
SINGLE LASHING AERIAL CABLE GUIDE This guide is economical but durable for new plant construction only. • Also suitable for use with fiber and coaxial cables • Has a 2 3/4 in. Cable Capacity • Cable shoe has a unique non-stick, highly polished stainless steel surface to minimize cable friction. • Replaceable shoe makes it easy to keep the guide like new
OVERLASH AERIAL CABLE GUIDE The Dual-Lashing Aerial Cable Guide is used to guide and straighten cables as they are pulled into a lashing position from a stationary or moving cable reel. • This unit offers the versatility of working for new installations or for overlashing cable to existing plant • Has a 2 3/4 in. cable capacity • Cast aluminum shoe with a steel insert on the face provides longer wear life • The shoe is suspended on steel straps from two strand rollers with safety lock preventing it from falling from the strand • All steel frame parts are plated for corrosion resistance • Weight: 11 lbs. (5kg)
The 'V-notch' of this sturdy block wedges on the strand for new build construction or two .750" cables fit between the frame and retaining pin for overlash jobs. The steel gate retains the cable being pulled out. The larger aluminum roller supports up to a 2" diameter cable and works well with winch lines.
UB1 Series Block with ball hook. These rugged universal blocks feature high strength and low weight at a value price. With a 2,500 lb SWL, they can be configured with 5 different mounting options. Permanently lubricated bearings provide long term durability and an extreme temperature operating range. • 8.1 – 13.0-lbs depending on configuration • 2,500-lb overhead SWL • 7” Block (O.D.) • Double shielded, deep groove ball bearings • 3” Sheave (rim width) • Permanently lubricated to withstand -5F to 250F • 3-1/8” Width (throat) • Profile machined groove for concentricity • Cast from A356 Aluminum and heat treated
No. 8 Clevis Universal Stringing Block For Suspending Blocks from Fixtures Features • May be used with any block that has a socket connector. • Strong, durable, and weather-resistant materials. • Max Working Load:  10,000 lbs • Steel, Heat Treated, Hot Dipped Galvanized.
Ball Hook Clevis for XS-100-B or GMP 74139 Stringing Block For Suspending Blocks from Fixtures KEY FEATURES • May be used with any Sherman & Reilly block that has a socket connector. • Strong, durable, and weather-resistant materials. • Steel, Heat Treated, Hot Dipped Galvanized.
Aerial Buddy (24")
Jameson Corporation
Jameson Aerial Sheave - 24in 24" Aerial Buddy recommended for set up, take down and turns. Sheave Designed To Protect ADSS Cable And Other Jacketed Fiber During Installation. Lift hoist swivels 360° and rotates 180° for unrestricted mounting and maneuverability. FEATURES • Spring loaded cable guard (patented) eliminates delays caused by cable and pull tape derailing. • 2” Opening allows pulling grips to pass through easily. • Lightweight, reinforced polymer weighs significantly less than aluminum and steel models. • Reduces installation fatigue, one-man set up. • Easy latching mechanism for single-handed operation. • High strength, impact resistant unit is more durable than aluminum. • Chemical, UV, corrosion resistant construction for longer life. • Electrically insulated* for safety. • Lift hoist swivels 360° and rotates 180° for unrestricted mounting and maneuverability   * 100 KV/Ft Dielectric Strength of Polymer Components Stainless Steel Fasteners
7/8 in. (22.23mm) made from high quality aluminum The Break-away Swivel give you invaluable protection when pulling either fiber optic or coaxial cable. • These simple tools provide an inexpensive fracture point between the pulling line and cable avoiding costly cable damage if the cable's rated pulling capacity is exceeded   • The design of the swivels incorporates a replaceable tension bolt that joins the barrel eye and swivel body. The bolt separates when pulling loads on the cable reach +/-5%. The damaged bolt can then be replaced in seconds using an Allen Breakaway BoltWrench (included) and screwdriver. •The swivel and bolt head are color-coded for fast load identification GMP uses a steel thrust washer and bushing in the larger break-away swivel and four (4) ball bearings in the smaller version. Both designs provide smooth rotation under load and help to keep twisting forces from reaching the cable. The larger break-away swivel, 7/8 in. x 4-5/8 in. (22.2mm x 114.3 mm) is machined from aluminum alloy with a black anodized finish for wear resistance. We offer six (6) standard bolt strengths ranging from 340 lbs. (154kgs) to 1200 lbs. (544kgs). The smaller break-away swivel, 5/8 in. x 3 1/4 in. (15.9mm x 95.2mm) is made of steel with a zinc plating finish for wear resistance. We offer eleven (11) standard bolt strengths ranging from 200 lbs. (91kgs) to 700 lbs. (317kgs). When placing fiber optic cable, 600 lbs. (272kgs) has been the industry standard for maximum load tension on the cable. With the inclusion of Fiber Optic cable in new OSP designs for broadband construction such as FTTx, you can choose from our list of appropriate break points matching the cable manufacturer's specification. When ordering a swivel(s) please keep in mind the need to also order a few replacement bolts. This will avoid delays in work if the bolt supplied with the swivel(s) breaks. Delays can then occur while waiting for replacement bolt(s) to be ordered from the factory. Note: The bolt design of the 5/8 in. swivel is slightly different from the bolt of the 7/8 in. swivel. Therefore, the bolts are not interchangeable between the two (2) sizes of swivels. Please consult the factory for a breaking strength not listed among our standard sizes.
5/8 in. (15.88mm) made from high quality aluminum The 5/8 in. size is extremely convenient when working with innerduct sizes below 1 5/8 in. in diameter   The Break-away Swivel give you invaluable protection when pulling either fiber optic or coaxial cable. • These simple tools provide an inexpensive fracture point between the pulling line and cable avoiding costly cable damage if the cable's rated pulling capacity is exceeded   • The design of the swivels incorporates a replaceable tension bolt that joins the barrel eye and swivel body. The bolt separates when pulling loads on the cable reach +/-5%. The damaged bolt can then be replaced in seconds using an Allen Breakaway BoltWrench (included) and screwdriver. •The swivel and bolt head are color-coded for fast load identification GMP uses a steel thrust washer and bushing in the larger break-away swivel and four (4) ball bearings in the smaller version. Both designs provide smooth rotation under load and help to keep twisting forces from reaching the cable. The larger break-away swivel, 7/8 in. x 4-5/8 in. (22.2mm x 114.3 mm) is machined from aluminum alloy with a black anodized finish for wear resistance. We offer six (6) standard bolt strengths ranging from 340 lbs. (154kgs) to 1200 lbs. (544kgs). The smaller break-away swivel, 5/8 in. x 3 1/4 in. (15.9mm x 95.2mm) is made of steel with a zinc plating finish for wear resistance. We offer eleven (11) standard bolt strengths ranging from 200 lbs. (91kgs) to 700 lbs. (317kgs). When placing fiber optic cable, 600 lbs. (272kgs) has been the industry standard for maximum load tension on the cable. With the inclusion of Fiber Optic cable in new OSP designs for broadband construction such as FTTx, you can choose from our list of appropriate break points matching the cable manufacturer's specification. When ordering a swivel(s) please keep in mind the need to also order a few replacement bolts. This will avoid delays in work if the bolt supplied with the swivel(s) breaks. Delays can then occur while waiting for replacement bolt(s) to be ordered from the factory. Note: The bolt design of the 5/8 in. swivel is slightly different from the bolt of the 7/8 in. swivel. Therefore, the bolts are not interchangeable between the two (2) sizes of swivels. Please consult the factory for a breaking strength not listed among our standard sizes.
Used to form the standard 12” flat bottom loop in small diameter cables, the tool is molded of resilient plastic. Universal ‘V-groove’ hand forming tool is recommended for .412, .500, .500MC2, .540 and .565 cable diameters only. The Mullen Bender is available for one cable formation or dual cable formation as indicated in the table below. This lightweight tool should be tethered to prevent falling and breakage, especially in cold weather.     Specifications:  - Cable Capacity: 1  - Weight: 1.4lbs
Lemco's M-200 Dual Mullen Bender is used to form the standard 12” flat bottom loop in small diameter cables, the tool is molded of resilient plastic. Universal ‘V-groove’ hand forming tool is recommended for .412, .500, .500MC2, .540 and .565 cable diameters only. This lightweight tool should be tethered to prevent falling and breakage, especially in cold weather. Specifications:  - Cable Capacity: 2  - Weight: 2.8lbs
Reel Buck
Lemco
A quick, easy and economical way to set up 18" and 22" strand reels and cable reels up to 54" in diameter. The foot and handle design holds the main frame up and away from irregular surfaces. The rugged steel tubing makes the Reel Buck tough enough for the construction site. The collapsible frame features an arbor retainer that uses quick release pins that are also used when the reel is loaded. Specifications: - Height: 35" - Length: 64" - Capacity: 850 lbs. - Weight: 60 lbs.
Our Number one seller. 1" plastic roller. Quick, slap-on design and single 1" channel for pulling cable in overlash construction. Designed prevent cables from catching or snagging. Supports cables up to 1" in diameter including fiber optic cable.
Dual Cable Roller Slide Stop - Dual 1" plastic rollers. Designed to prevent cables from catching or snagging. This cable roller comes with two separated 1" channels for pulling multiple cables in overlash construction. Supports cables up to 1" in diameter including fiber optic cable.
3" Cable Roller Slide Stop - 3" rubber roller. Designed prevent cables from catching or snagging. Supports cables up to 3" in diameter including fiber optic cable.
This unit is designed to pull out up to four cables and works on packages up to 2 3/4" in diameter. Opposing roller arms retain the puller to the existing cable and offer quick pole transfer. Polyurethane rollers fitted with bronze bearings yield high mileage production. The steel frame is protected by a black polyester powder coat. Wt. 6.3 lbs.
90-Degree Corner Block ( Dual )
Jameson Corporation
90-Degree, Dual Row Corner Block   Easy Cable Pulling Around Corners • Jameson corner blocks evenly distribute pressure on coax or fiber cable when pulling around corners. They feature steel side plates with a straight base that acts as a strut for increased strength. • For greater options, steel side plates can be replaced in the  eld and all Jameson corner blocks are interchangeable with alternative set-up brackets. • Component parts for 60 and 90 degree blocks are fully interchangeable.
90-Degree Corner Block ( Single )
Jameson Corporation
90-Degree, Single Row Corner Block   Easy Cable Pulling Around Corners • Jameson corner blocks evenly distribute pressure on coax or fiber cable when pulling around corners. They feature steel side plates with a straight base that acts as a strut for increased strength. • For greater options, steel side plates can be replaced in the  eld and all Jameson corner blocks are interchangeable with alternative set-up brackets. • Component parts for 60 and 90 degree blocks are fully interchangeable.
60-Degree Corner Block ( Dual )
Jameson Corporation
60-Degree, Dual Row Corner Block   Easy Cable Pulling Around Corners • Jameson corner blocks evenly distribute pressure on coax or fiber cable when pulling around corners. They feature steel side plates with a straight base that acts as a strut for increased strength. • The 60 degree model offers more versatility than the standard 45 degree blocks with the majority of system designs. • For greater options, steel side plates can be replaced in the  eld and all Jameson corner blocks are interchangeable with alternative set-up brackets. • Component parts for 60 and 90 degree blocks are fully interchangeable.
60-Degree Corner Block ( Single )
Jameson Corporation
60-Degree, Single Row Corner Block   Easy Cable Pulling Around Corners • Jameson corner blocks evenly distribute pressure on coax or fiber cable when pulling around corners. They feature steel side plates with a straight base that acts as a strut for increased strength. • The 60 degree model offers more versatility than the standard 45 degree blocks with the majority of system designs. • For greater options, steel side plates can be replaced in the  eld and all Jameson corner blocks are interchangeable with alternative set-up brackets. • Component parts for 60 and 90 degree blocks are fully interchangeable.
Pole Mount Bracket (Dual Row)
Jameson Corporation
For Dual Corner Corner Block   Whether working from the ground or in the air, Jameson’s aerial construction tools make cable placement easier and safer. • Designed to save vertical space on crowded joint occupied poles, brackets are ideal for mounting single, dual or quad corner blocks on the pole. • Innovative nylon strap and ratchet make Jameson pole- mount brackets easy to use. Bracket base is contoured to  t pole for maximum stability. • Ratchet strap will not damage existing cables and weighs less than chain straps. Can be adjusted to work from right or left hand side for convenient operation.
Pole Mount Bracket (Single Row)
Jameson Corporation
For Single Row Corner Block   Whether working from the ground or in the air, Jameson’s aerial construction tools make cable placement easier and safer. • Designed to save vertical space on crowded joint occupied poles, brackets are ideal for mounting single, dual or quad corner blocks on the pole. • Innovative nylon strap and ratchet make Jameson pole- mount brackets easy to use. Bracket base is contoured to  t pole for maximum stability. • Ratchet strap will not damage existing cables and weighs less than chain straps. Can be adjusted to work from right or left hand side for convenient operation.
Versa Block Stringing Block
Jameson Corporation
Versa Block with Rubber Roller is ideal for use with cable up to 1.5" in diameter. Versa Blocks offer the versatility of stringing cable at midspan on new and existing overlash construction. Provides easy cable placement from aerial buckets or the ground when used with Jameson's lay-up sticks and wire raising tool. Low-profile frame reduces cable damage as it passes through block and wide keeper arm accommodates large cable bundles when used as overlash block.
Versa Block with Aluminum Roller is ideal for up to 2.5" diameter cable or bundles and winch lines. Versa Blocks offer the versatility of stringing cable at midspan on new and existing overlash construction. Provides easy cable placement from aerial buckets or the ground when used with Jameson's lay-up sticks and wire raising tool. Low-profile frame reduces cable damage as it passes through block and wide keeper arm accommodates large cable bundles when used as overlash block.
Easy Rider Overlash Block with Nylon Roller   Easy Cable Placement From Aerial Buckets Whether working from the ground or in the air, Jameson’s aerial construction tools make cable placement easier and safer.   Easy RiderTM Overlash Blocks Economical and lightweight, yet the high strength steel frame maintains cable alignment. Easily snaps over a strand and cable package up to 2.25” in diameter. The 1.5” width provides convenient stacking when pushed by lasher. Features a high, rounded bonnet to prevent block kicking under lasher. Stacks evenly. Non-binding roller axle allows rollers to “ride easily” and rotate smoothly.
The block is used to support up to 2¾" telephone, fiber or coaxial cable prior to the lashing operation. The frame and sheave are cast of aluminum.    PY-750 - 1/4" strand
This block supports cable in mid-span during pull-out and lashing operations. The block has four nylon rollers that support up to 1" cable. 
4 ROLLER CABLE BLOCK This block can support multiple cables during new strand construction. • Can accommodate four 1 in. (25mm) cables on nylon rollers • Locking gates keep cable(s) on the rollers • Weight: 3.5 lbs. (1.59 kgs.)  
Cable Puller
Lemco
This Puller is used to pull out cable prior to the lashing operation. The main body of the Puller is a rugged one-piece aluminum casting. Two hardened steel rollers are provided to ride on either 5/16" or 1/4" strand. When pull-out pressure is released, a brake automatically holds the Puller in position. Pull-out pressure releases the brake. For best results, attach the cables in a balanced manner.
Pole Sling
Klein
• For use where a running loop wrap around pole is desired. • Nylon web stitched with nylon thread. • NOT an occupational protective device. NOT for human support.   Rated Capacity Choke Hitch: 3000 lbs. (1350 kg) Rated Capacity Basket Hitch: 4700 lbs. (2115 kg) Overall Length: 39'' (990.6 mm) Width: 2'' (50.8 mm)
• Round, smooth inside jaw contour on this series of grips is ideal for bare ACSR, aluminum, and stranded copper cables • Smooth jaws grip with maximum contact and are less likely to damage conductors   Cable Diameter: 0.20''(5.1 mm) to 0.40'' (10.2 mm) Jaw Length: 4'' (101.6 mm) Application: Bare ACSR, Aluminum and Stranded-Copper Cables Special Features: Spring Loaded Sub Brand: Chicago Grip
This Klein Tools 1613-40 Chicago Grip is designed for EHS, Messenger, and Guy Strand cable. The double V grooves provide four-point contact, which reduces chances of slipping and also provides proper alignment of wire and cable. All Klein grips are manufactured from custom drop-forged steel that is machined and heat treated for excellent durability. Each grip is individually hand inspected and actuated for proper function. Grips are also rigorously tested and pulled to rated load to ensure the highest quality and reliability. • Works with aircraft, EHS, messenger and guy strand cable • Designed for cable sizes from 0.12 to 0.37-Inch (3.10 to 9.40 mm) • Double ''V'' grooves give four-point contact, reducing chance of slipping and providing proper alignment of wire and cable • Sawtooth profile provides extra gripping power • 4500-Pound (2041 kg) Maximum Safe Load • For larger conductors, see our grips with round inside-jaw contour • Locking handle keeps jaw open while grip is placed on cable with a hot stick   Cable Diameter: 0.12" to 0.37" (0.3 to 0.9 cm) Jaw Length: 4.188'' (10.6 cm) Application: Extra-High-Strength Cables, Messenger, Guy Strand Cable Type: Aircraft, EHS, Messenger, Guy Strand Jaw Type: Double V Sub Brand: Chicago Grip
• Designed for use when light, compact grip is desired and where conductor damage is not a factor • Gripping pressure of the knurled jaw is applied to 1/4-Inch (6.35 mm) cable area • Maximum safe load is 5000-pounds • Individually hand inspected and actuated for proper function • Rigorously tested and pulled to rated load to ensure the highest quality and reliability   Cable Diameter: 0.125'' to 0.500'' (3.18 to 12.70 mm) Cable Type: Messenger and Guy Strand Maximum Safe Load: 5000 lb (2268 kg) Weight: 2.2 lb (1.0 kg)
• Designed for use when light, compact grip is desired and where conductor damage is not a factor. • Gripping pressure of the knurled jaw is applied to 1/4'' (6.35 mm) cable area. • Has a swing latch to help hold cable in the jaw. • Cable Diameter: 0.20''(5.1 mm) to 0.40'' (10.2 mm) • Jaw Length: 4'' (101.6 mm) • Application: Bare ACSR, Aluminum and Stranded-Copper Cables • Special Features: Spring Loaded • Sub Brand: Chicago Grip   Cable Diameter: 0.28'' (7.11 mm) to 0.75'' (19.05 mm) Weight: 4 lbs. (1.81 kg) Sub Brand: Klein Havens  
Klein Havens Grip with Swing Latch for Wire Rope (.125" - .50") Designed for use when light, compact grip is desired and where conductor damage is not a factor. Gripping pressure of the knurled jaw is applied to 1/4'' (6.35 mm) cable area. Has a swing latch to help hold cable in the jaw.   Maximum Safe Load: 5000 lb (2268 kg)
Wire Vise ( .091 - .114" )
Senior Industries
.091" - .114" Wire Range • Used to deadend galvanized steel messenger mid-span of a service drop • Rated to hold a minimum of 90% of RBS of wire specified • Designed to support both ends of self-supporting multi-pair drop wire that uses a solid galvanized steel messenger wire that is integrated into the jacket in a figure-8 configuration   Overall Length:     5.5" Cartridge Length: 1.47" Bail Width:     1.60" Wire Range: .091" - .114" or 2.3 - 2.9mm      
Wire Vise ( .120 - .135")
Senior Industries
.120" - .135" Wire Range • Used to deadend galvanized steel messenger mid-span of a service drop • Rated to hold a minimum of 90% of RBS of wire specified • Designed to support both ends of self-supporting multi-pair drop wire that uses a solid galvanized steel messenger wire that is integrated into the jacket in a figure-8 configuration   Overall Length:  7.70" Cartridge Length: 2.46" Bail Width: 1.50" Wire Range:  .120-.135, 11 USSWG, 10 USSWG  
Hoist (1-ton)
Hubbell
Hoist is proof-tested and factory-operated at 150% of capacity rating. Lightweight high-strength handle and sheave housings are heat-treated aluminum. All working parts are fully enclosed in the housing unit to protect the hoist mechanism and to cover the gearing for worker safety. Chain is high-strength alloy steel, polished for smooth action and low wear. Load hooks are forged steel with spring-loaded latches. Both top and bottom hooks swivel 360° to allow for unwinding action of rope or stranded cable under tension. For easy hook-up, chain release to freewheel but only under no-load conditions. Controls automatically lock when hoist is pulling a load. Two simple levers . . . Shift Key for up and down, on top housing, and Release Key in handle recess . . . are easy to switch, even wearing gloves. Simply by ratcheting one or two clicks per stroke in up or down mode, operator can choose quick speed of a full link or half-link rate for extra accuracy. For cramped-quarters work, ratchet handle swings to either side. This provides option of push or pull stroke to best suit conditions and preferences. Each unit comes with an illustrated Operating Manual, includes complete parts list. Lifetime oil-impregnated bronzesleeve bearings require no additional lubrication. Normal low maintenance calls for only routine inspection. Pliers and screwdriver are the only tools needed.   Product Specifications Product Type:                    Chain Hoist Product  Hoist:                  Style  Link Chain Load Rating:                      1 ton (907 kg) Handle Pull at Rating:      90 lbs. (41 kg) Hook-to-Hook Min:          11" (279.4 mm) Standard Lift Distance:    5.5' (1.7 m.) Weight:                               14.21 lbs
3/4 Ton Lever Chain Ratchet Hoist.   Features • Standard overload clutch • Double pawl Weston style load brake • Fully machined steel load sheaves • Cast steel hook latches • Fully enclosed gear train and caged internal bearings • All exposed parts plated or powder coated for corrosion protection • Double pawl Weston style load brake • Conforms to ASME B30.16 - Chain Hoists and Standard B30.21 - Lever Hoists
10-foot, 1-1/2 ton Lever Chain Hoist.  Lift-All hoists are perfect for a low-headroom lift. This durable, and lightweight hoist is an excellent option for a variety of lifting applications. The fully enclosed gears are protected from contamination. Powder-coated and plated finishes on exposed components protect the hoists from corrosion.  All gears and shafts run on caged roller bearings for smooth operation and long life (excludes mini pullers).  The Lever Chain Hoist can be used with one-hand operation and set-up. Featuring a non-slip rubber grip and 360° lever rotation, this hoist requires minimal space to operate in any orientation. Drop forged alloy hooks are designed to stretch before chain failure when overloaded.   Features • Economical and easy to operate. • Powder-coated or plated housing and hooks protect from corrosion. • Fully enclosed gearing protects from contamination. • Enclosed, self-adjusting Weston style mechanical load brake. • The lever chain hoist has easy one-hand operation and set-up and operates in any orientation.     Meets ASME/ANSI B30 and NASA-STD-8719.9 standards.
10-foot, 1-1/2 ton Lever Chain Ratchet Hoist.   Features • Standard overload clutch • Double pawl Weston style load brake • Fully machined steel load sheaves • Cast steel hook latches • Fully enclosed gear train and caged internal bearings • All exposed parts plated or powder coated for corrosion protection • Double pawl Weston style load brake • Conforms to ASME B30.16 - Chain Hoists and Standard B30.21 - Lever Hoists
The Towing Lanyard is used with all GMP lashers. The lanyard snap hook connects to the ring on the towing bridle for pulling a lasher from ground level. A loop is spliced to one end of the 35 X 3/8" foot lanyard and a forged hook with safety snap is on the other. It is recommended that this polypropylene lanyard only be pulled by hand. Maximum Working Load Limit is 250 lbs. (113 kg
Simple & effective, this block handles cable or bundles up to 4". • The roller is made from industrial conveyor bearing material for high abrasion resistance with low rolling friction • A spring-latch gate encloses cable & strand within the frame • Steel frame allows "in field" straightening if dropped or bent • A narrow profile & stackable design allows for high density storage
FLEXIBLE CABLE PULLING GRIPS Pulling Grips, sometimes referred to as pulling socks or stockings, are indispensable in many different cable pulling applications. • Manufactured from high-tensile, galvanized steel wire that is evenly hand woven in a single, double or triple wire weave according to pulling tension requirements • We reverse weave our grips which create a loop at the end of the grip instead of being crimped or soldered together. The wire is then joined under the crimped head. This creates a higher quality product that outlasts the competition.   Diameter Range:   0.24 to 0.51in. (6 to 13 mm) Minimum Breaking Strength:   1984 lbs. (900 kg) Grip Length:   11.81 in. (300 mm)  
FLEXIBLE CABLE PULLING GRIPS Pulling Grips, sometimes referred to as pulling socks or stockings, are indispensable in many different cable pulling applications. • Manufactured from high-tensile, galvanized steel wire that is evenly hand woven in a single, double or triple wire weave according to pulling tension requirements • We reverse weave our grips which create a loop at the end of the grip instead of being crimped or soldered together. The wire is then joined under the crimped head. This creates a higher quality product that outlasts the competition.   Diameter Range:   0.75 to 0.98 in. (19 to 25 mm) Minimum Breaking Strength:   4674 lbs. (2120 kg) Grip Length:   23.62 in. (600 mm)  
FLEXIBLE CABLE PULLING GRIPS Pulling Grips, sometimes referred to as pulling socks or stockings, are indispensable in many different cable pulling applications. • Manufactured from high-tensile, galvanized steel wire that is evenly hand woven in a single, double or triple wire weave according to pulling tension requirements • We reverse weave our grips which create a loop at the end of the grip instead of being crimped or soldered together. The wire is then joined under the crimped head. This creates a higher quality product that outlasts the competition.   Diameter Range:   0.47 to 0.75 in.  Minimum Breaking Strength:   3505 lbs.  Grip Length:   21.65 in.  
Pulling Grip (20'' Long)  1'' to 1.2'' Diameter   KPS Heavy Duty Medium Length 1.00'' to 1.24'' cable diameter (1 1-15/64'' or 25.40 31.35 mm).   Mesh Length: 20'' (508 mm)
Stainless Steel Lashing Wire 302 Stainless .045" x 1200' Coil   Stainless Steel Lashing Wire is used in a lasher to lash an aerial cable or combination of cables to a supporting strand. • A specially controlled annealing process yields a uniform,fine grain structure throughout wire length and cross section for best results   Type 302 Stainless • 18% chromium, 8% nickel analysis • This wire has excellent resistance to corrosion from industrial atmospheres • Its higher tensile strength and breaking load are an added benefit • A .038 in. diameter Type 302 wire provides strength equal to a .045 in. type 430 wire with better ductility (easier bending and unwinding) and better elongation (less chance of wire breakage from stress)  
Stainless Steel Lashing Wire 430 Stainless .045" x 1200' Coil   Stainless Steel Lashing Wire is used in a lasher to lash an aerial cable or combination of cables to a supporting strand. • A specially controlled annealing process yields a uniform,fine grain structure throughout wire length and cross section for best results   Type 430 Stainless • Low carbon, 17% chromium wire • Suitable for general use and in ordinary atmospheric exposure • Will acquire only a dark surface stain • Specifically not recommended for use within 25 miles of salt water or industrial operations which emit pollutants  
The latest word in aerial cable lashing. Perfect for all telcom cable construction, including Coaxial and FTTx cable. With its light weight and parallel-pull capability, you'll string cable quickly and easily, over all outside plant cable routes. From the company that pioneered the modern automatic lasher with Western Electric back in the 1940's.... comes Apollo... a machine that's lightweight, easy-to-handle and simple to operate and maintain. The newest addition to GMP's line of proven lashers, Apollo has all of the versatility and performance features you need to easily handle today's broadband lashing applications, solving all of the problems associated with pulling parallel to the strand and through densely crowded cable routes. GMP engineers designed Apollo using computer-aided design and finite element analysis to achieve its high degree of durability without any excess weight. Then, we employed the very latest in high-speed CNC machining to make every part fit and perform exactly as designed. Like all our lashers, Apollo is built to last. After all, this is not just any spinner, it's a GMP lasher.   No other lasher or cable spinner will give you all of these advanced features and operating benefits: • Lashes any telcom cable/innerduct combination up to 4 in. (10 cm) diameter • Parallel-pull capability overcomes all terrain obstacles • Interference-free over-lashing with no modifications • Positive slip-free gear drive (no belts) tested in excess of 1 million cycles • Lashes to strand sizes 1/4 in. to 3/8 in. (6 - 10 mm) diameter lasher in use • Holds two coils of industry standard wire .045 in. x 1200 ft. (1.1 mm x 365 m) or .038 in. x 1600 ft. (1. mm x 488 m) • Provides adjustable tension of lashing wire, affording tight or loose lash • Wire tension constant regardless of amount on spool • No lasher backroll when pulling force removed • Front rollers guide cables through the machine • All smooth edges throughout provide 360° protection against cable damage • Ergonomic design makes it easy to handle • Manual clutch release allows speedy span transfers fully serviceable to "good-as-new" specifications • The Apollo and every GMP lasher is fully serviceable to "good-as-new" specifications at our factory and at factory-trained service locations around the globe. • Protected by U.S. Patents #6,398,189 and #6,062,542 Each Apollo lasher also includes a 6 ft. (2 m) towing bridle and a rugged, weather-tight storage chest to securely protect your lasher investment while it's not in use.  
J2 Cable Lasher Standard Wire Diameter: .045 The Model J2 Cable Lasher is used to lash a single aerial cable or numerous cables to a supporting strand or to an existing lashed cable with stainless steel lashing wire. • Will lash any single or multiple aerial cables up to 3 in. (76 mm) diameter across on any suspension strand from 1/4 in. (6 mm) to 7/16 in. (11 mm). A factory modification will allow the lasher to accommodate 1/2 in. (12.7 mm) strand if necessary. 86070 J2 Cable Lasher with Case • Consists of a rotating drum supported on a carriage that provides the mounting for a driving mechanism, cable lifters, cable and strand rollers • Each of two recessed magazines will hold a 1200 ft. coil of .045 in. (365 m of 1.1 mm wire) lashing wire (or 450 ft. of .065 in.). The Lashing Wire is fully recessed and covered by a gate. • Features a fast setup procedure, quick coil loading, and automatic drum lock for easy span transfers and smooth forward travel   • J2 Lashers make overlashing easy. Just push down on the strand roller knob, rotate it a quarter turn and you can lash additional cables together on previously lashed cable • Positive internal gear to gear mechanism has no chains or belts to stretch, slip or break • Constructed with heat-treated, plated steel, stainless steel, brass and aluminum components. Contains sealed and oiless bearings to minimize maintenance and assure durability.   • Pre-drilled and tapped at the factory for mounting of the lasher guard or "halo". For use when lashing in overgrown areas. fully serviceable to "good-as-new" specifications• The J2 and every GMP lasher is fully serviceable to "good-as-new" specifications at our factory and at factory-trained service locations around the globe. • The lasher is furnished with a rugged lightweight storage chest with corrosion resistant hardware, recessed latches and a moisture-proof, tongue-in-groove design for maximum protection when not in use • Supplied with a 6 ft. bridle rope assembly and snap hooks, and an information and operation manual
MODEL C2 CABLE LASHER The compact Model C2 Cable Lasher is perfect for lashing smaller diameter aerial cables to supporting strand with stainless steel lashing wire. The new design improvements make the C2 equally suited for new construction or overlashing up to its full 1 7/8 in. bundle capacity. • Lashes single or bundled cables up to 1 7/8 in. (46mm) onto strand sizes 1/4 in. to 3/8 in. (6-10mm) diameter • New style strand lock swings out of the way for unobstructed overlashing • Simple wire routing yields either “normal” or “loose” wire tension • Dual wire magazines for loading two coils of stainless steel lashing wire • Typical wire dimensions: 1200 ft. x .045 in. (365 m x 1.1mm) or 1600 ft. x .038 in. (487m x 1mm) • Lightweight and compact: Unloaded weight 35 lbs. (16kgs.); only 10 in. O.D. x 18.5 in. long (25 x 47cm). The C2’s tapered housing eases passage through treed areas • The C2 Cable Lasher is furnished with a 6 ft. (1.6m) bridle rope with snap hooks, an instruction manual and a rugged, lightweight storage chest • The C2 and every GMP lasher is fully serviceable to “good-as-new” specifications at our factory and at factory-trained service locations around the globe • Like all GMP lashers, the C2 is built to last for many years of service. Components are CNC machined from alloy steel, stainless, bronze and aluminum castings to exacting tolerances and treated to withstand corrosion. Gear drives and sealed bearings assure maximum durability with minimal maintenance.
M-Series Loop Forming Tool Easy-grip pawl ensures positive engagement into gear rack. Bronze bushings provide smooth operability and prevent galling. Frame and gear rack are attached with a reinforcement plate to withstand pressure when forming dual trunk cables. Synthetic shoes driven by vertical gear rack form loop. The M-3206 produces 36” overall length loop. Cable Capacity 2 (.750")  
M-Series Loop Forming Tool Easy-grip pawl ensures positive engagement into gear rack. Bronze bushings provide smooth operability and prevent galling. Frame and gear rack are attached with a reinforcement plate to withstand pressure when forming dual trunk cables. Synthetic shoes driven by vertical gear rack form loop. The M-3195 produces 45-1/2” overall length loop. Cable Capacity 2 (1.0")  
This tough swivel is designed to handle higher thrust loads for extra cable safety and faster straight pulls. • Precision-machined body is made of high quality stainless steel with higher working load ratings than comparably sized swivels available on the market • Heavy-duty swivel that is built with a thrust bearing for tensile load and a radial bearing for bending load • Working Load Limit for under ground applications is based on a horizonal pull of 3:1 while aerial applications have a WLL of 5:1 CAUTION: To be used for underground cable installation only. Note: These swivels are Not Designed for Directional Drilling applications. They are designed for pulling cable or rope. Do not allow these swivels to be pulled around a bullwheel or capstan. Damage to the swivel and/or wheel may occur. Working Load Limit Under Ground:   2250 lbs Working Load Limit Aerial:   1350 lbs Eye Width:   3/8 inch
This tough swivel is designed to handle higher thrust loads for extra cable safety and faster straight pulls. • Precision-machined body is made of high quality stainless steel with higher working load ratings than comparably sized swivels available on the market • Heavy-duty swivel that is built with a thrust bearing for tensile load and a radial bearing for bending load • Working Load Limit for under ground applications is based on a horizonal pull of 3:1 while aerial applications have a WLL of 5:1 CAUTION: To be used for underground cable installation only. Note: These swivels are Not Designed for Directional Drilling applications. They are designed for pulling cable or rope. Do not allow these swivels to be pulled around a bullwheel or capstan. Damage to the swivel and/or wheel may occur. Working Load Limit Under Ground:   5000 lbs Working Load Limit Aerial:   3000 lbs Eye Width:   17/32 inch
This tough swivel is designed to handle higher thrust loads for extra cable safety and faster straight pulls. • Precision-machined body is made of high quality stainless steel with higher working load ratings than comparably sized swivels available on the market • Heavy-duty swivel that is built with a thrust bearing for tensile load and a radial bearing for bending load • Working Load Limit for under ground applications is based on a horizonal pull of 3:1 while aerial applications have a WLL of 5:1 CAUTION: To be used for underground cable installation only. Note: These swivels are Not Designed for Directional Drilling applications. They are designed for pulling cable or rope. Do not allow these swivels to be pulled around a bullwheel or capstan. Damage to the swivel and/or wheel may occur. Working Load Limit Under Ground:   7000 lbs Working Load Limit Aerial:   4200 lbs Eye Width:   9/16 inch
This tough swivel is designed to handle higher thrust loads for extra cable safety and faster straight pulls. • Precision-machined body is made of high quality stainless steel with higher working load ratings than comparably sized swivels available on the market • Heavy-duty swivel that is built with a thrust bearing for tensile load and a radial bearing for bending load • Working Load Limit for under ground applications is based on a horizonal pull of 3:1 while aerial applications have a WLL of 5:1 CAUTION: To be used for underground cable installation only. Note: These swivels are Not Designed for Directional Drilling applications. They are designed for pulling cable or rope. Do not allow these swivels to be pulled around a bullwheel or capstan. Damage to the swivel and/or wheel may occur. Working Load Limit Under Ground:   10,000 lbs Working Load Limit Aerial:   6000 lbs Eye Width:   11/16 inch
This tough swivel is designed to handle higher thrust loads for extra cable safety and faster straight pulls. • Precision-machined body is made of high quality stainless steel with higher working load ratings than comparably sized swivels available on the market • Heavy-duty swivel that is built with a thrust bearing for tensile load and a radial bearing for bending load • Working Load Limit for under ground applications is based on a horizonal pull of 3:1 while aerial applications have a WLL of 5:1 CAUTION: To be used for underground cable installation only. Note: These swivels are Not Designed for Directional Drilling applications. They are designed for pulling cable or rope. Do not allow these swivels to be pulled around a bullwheel or capstan. Damage to the swivel and/or wheel may occur. Working Load Limit Under Ground:   25,000 lbs Working Load Limit Aerial:   15000 lbs Eye Width:   1-1/32 inch
This block lets you overlash to cable bundles up to 2 in. (50mm) across ... and its affordability lets you use more blocks for smoother, neater lashing on new or rebuild construction. • Ideally suited for messenger strands from 1/4 to 3/8 in. (6-10 mm) • Easy to raise and attach with GMP's Wire Raising Tool • A keeper retains the block on the messenger, and the fiber cable is positively retained in the block. • The block's gritty non-skid surface rests against the strand and minimizes sliding during the pulling in of cable • The frame is made of zinc-plated steel and is designed for the optimum strength-to-weight ratio • The frame is equipped with an anti-friction roller and a lever actuated keeper bar which encloses the cable in the block • Installation is straightforward. With the lever in the vertical position, just hook the block onto a wire raising tool through the hole in the lever and raise the block to hook it onto the strand. Now swing the lever to the horizontal position with the tool to close and lock the keeper bar into the detent While low priced and lightweight, it is built to demanding GMP quality standards. This block may also be used for placing small copper or coaxial cable as well.
This Cable Block is perfect for temporarily supporting any cable up to 2 3/4 in. (70mm) diameter on 1/4 - 3/8 in. (6-10mm) dia. suspension strand during new construction or while overlashing to existing lashed cable. • The frame and sheave are made from 100% heat treated aluminum alloy • Oilite bearings on the sheave and steel inserts on the underside of each strand hook provided for smoother operation and less wear and tear • Built-in lever controls both the keeper and spring-loaded cam during installation and removal • The cam holds the block firmly in position during pulling in, then releases during lashing so that the block can travel ahead of the lasher towards the end of the span • Optional spring loaded keeper is available to keep smaller cables captured in the pulley Weight:  F Cable Block   3 lbs.12 oz.    
Box of 100 pcs.   Perfect for temporary and permanent terminations or grounds, this all steel clamp lets you securely attach two lashing wires or #6 ground wire on any size strand from 1/4 to 7/16 in. (6-11 mm) diameter. • Two grooved plates fit on opposite sides of the strand D Lashing Wire Clamp •Plates secured by a threaded stud with a flanged shoulder and washer to block slippage, and two hexagonal nuts: one on the long end of the stud to tighten the clamp, one on the other end to terminate the wire against the two washers • A mechanical galvanized finish provides extra corrosion resistance